DG419LEUA+T Interface - Analog Switches, Multiplexers, Demultiplexers by Maxim Integrated

Defines the switch topology, such as 2:1, 4:1, or 8:1, indicating how many inputs are routed to outputs. Essential for selecting the correct multiplexer for signal routing in your design. Check the datasheet for channel count and switching characteristics.

Maximum resistance between the switch terminals when the device is fully on. Lower values reduce power loss and heat. Compare this parameter when selecting MOSFETs, IGBTs, or relays for high-current circuits. Always verify against the datasheet for your operating conditions.

Highest supply voltage at which the component can operate normally without damage or performance degradation. Exceeding this limit may cause overheating or failure. Always check this parameter against your power supply design to ensure the component operates within its safe voltage range for reliable long-term performance.

Specifies the triac construction or series, such as standard, snubberless, or logic-level. This affects switching performance, gate sensitivity, and commutation capability. Verify the exact type against the datasheet to ensure compatibility with your circuit's voltage, current, and triggering requirements.

Typical current consumed by the component in standby or idle state, measured in milliamperes. This is important for battery-powered or low-power applications. Compare this value with your power budget to ensure the component does not drain excessive current when inactive, affecting overall system efficiency.

This is the on-state resistance between the drain and source terminals of a MOSFET. It affects power dissipation and efficiency. Lower values are preferred for high-current switching. Always check the datasheet for the specified test conditions, as RDS(on) varies with gate voltage and temperature.

Indicates the construction or configuration of the transformer, such as flyback, forward, or planar. Affects performance, size, and application suitability. Refer to datasheet for detailed specifications and recommended usage.

Specifies the lowest supply voltage at which the component remains fully functional. Compare this value with your system's power rail tolerance and verify it against the datasheet's recommended operating conditions to ensure reliable startup and operation.

Range of maximum data transfer rates supported by the component, expressed in kilobits per second. This indicates the span of possible speeds the device can handle. Compare this range with your system's required throughput to ensure the component can support the necessary communication bandwidth without data loss.

Total resistance is the end-to-end resistance of a component, such as a potentiometer or resistor network. It defines the maximum resistance available and is critical for circuit design. Verify this value against the datasheet to ensure proper operation.

Specifies the physical medium through which signals travel, such as fiber optic, twisted pair, or coaxial cable. This attribute is critical for ensuring compatibility with your network infrastructure and for meeting performance requirements. Verify the media type against your system's specifications and the component datasheet to avoid signal integrity issues.

Typical delay from the moment the turn-off signal is applied until the output begins to transition. This parameter affects switching losses and timing margins in power circuits. Compare with datasheet values to ensure your design meets required switching performance.

Specifies how many analog-to-digital and digital-to-analog converters are integrated in the component. This matters when selecting mixed-signal ICs for data acquisition or control systems. Verify against the datasheet to ensure the converter count matches your application requirements.

Specifies the typical signal loss introduced by the component under standard conditions. Compare this value across similar parts to match your circuit's allowable attenuation. Always verify against the datasheet for frequency and temperature dependencies.

Specifies the filter topology used in the component, such as low-pass, high-pass, band-pass, or notch. This determines the frequency response and attenuation characteristics. Engineers must verify the filter type against the datasheet to ensure it meets the required signal conditioning and interference rejection for the application.

Indicates whether the device automatically manages hardware flow control signals such as RTS and CTS. This feature reduces host processor overhead by handling handshaking in hardware. Verify support in the datasheet when designing UART or serial communication interfaces.

Number of turns in a coil or winding. Affects inductance, transformer ratio, and impedance. Critical for designing transformers, inductors, and magnetic components. Check datasheet for tolerance.

Highest data transfer rate the component can reliably support, typically in bits per second. This is critical for serial interfaces, modems, or transceivers. Ensure your application's required data throughput does not exceed this limit to avoid communication errors and performance degradation.

Specifies the maximum continuous voltage the component can safely withstand without damage or performance degradation. Critical for ensuring proper operating margins in power supplies, signal lines, and isolation barriers. Always confirm with the datasheet for absolute maximum ratings.

Specifies the ambient or case temperature at which the component's electrical and mechanical characteristics are guaranteed. Verify this value against the datasheet to ensure the part operates within its intended thermal environment and to avoid derating issues.

Minimum forward transconductance value for a transistor or amplifier. Indicates the minimum gain capability. Critical for ensuring sufficient amplification in your circuit. Verify against datasheet conditions.

Indicates protection features integrated into the component, such as overcurrent, overvoltage, or thermal shutdown. These safeguards help prevent damage during fault conditions. Verify which protections are included and their thresholds in the datasheet to ensure they meet your application's safety requirements.

Indicates whether the component supports automatic software flow control, a method using XON/XOFF characters to manage data transmission. Check this attribute when selecting UARTs, USB bridges, or communication modules to ensure compatibility with your system's flow control requirements.

Specifies the maximum allowable decrease from the nominal value for components like resistors, capacitors, or inductors. Engineers compare this to ensure worst-case performance still meets circuit requirements. Always verify against the datasheet for the specific part.

Specifies the maximum allowable upward deviation from the nominal value for this component parameter. Verify against datasheet limits to ensure your circuit tolerates the worst-case positive variation, especially for resistors, capacitors, and other passives.

Typical time delay between the input signal and the output activation, usually in nanoseconds or microseconds. This parameter is critical for timing-sensitive circuits. Ensure that the delay meets your system's timing requirements to avoid signal skew or improper switching behavior.

Indicates the lowest frequency at which the component's response begins to roll off. Compare this value with your signal bandwidth to ensure the part passes desired frequencies. Verify against the datasheet's frequency response curve for your operating conditions.

Power supply rejection ratio measures how well a regulator or amplifier attenuates supply noise and ripple. Higher PSRR means cleaner output. Critical for precision analog circuits and RF. Compare at relevant frequencies and load currents.

Lists the product categories or classifications assigned to this component, such as connectors, capacitors, or modules. This helps in filtering and comparing similar parts. Review the categories to ensure the component fits your application and to find alternative parts in the same class.

Indicates the specific product subcategories or classifications within the broader component family. Helps narrow down search results and identify the exact type of component needed for your design. Review the subcategory to ensure compatibility with your application.

Physical package or case type of the component, defining its dimensions, mounting style, and thermal characteristics. Common types include SMD, through-hole, BGA, and QFN. Choose the package that fits your PCB layout and assembly process. Verify the exact package code in the datasheet for footprint compatibility.

Identifies the company that designed and produced the component. Buyers often filter by manufacturer to ensure brand reliability, quality standards, and supply chain consistency. Verify the manufacturer against the datasheet and official packaging to avoid counterfeit parts.

Specifies the material of the component's outer casing, such as plastic, metal, or ceramic. This affects durability, thermal performance, and environmental resistance. Verify against datasheet for application-specific requirements like flammability or chemical exposure.

Position of the terminals on the package, such as dual-in-line, gull-wing, or J-lead. This affects PCB layout, soldering, and thermal performance. Engineers must ensure the terminal position matches the footprint and assembly capabilities of their manufacturing line.

Indicates the locking mechanism used to secure the connector or terminal in place. Choose the appropriate type for your application to ensure reliable mating and vibration resistance. Verify compatibility with the mating part and datasheet specifications.

Bit width of digital data processed by a converter, processor, or memory. Higher bits mean better resolution or precision. Verify against datasheet to match your system's data width and accuracy needs.

Indicates the maximum continuous wave input power the component can safely handle without damage or excessive distortion. Exceeding this limit may cause failure. Verify this value against your signal power and consider peak-to-average ratio in modulated systems.

Indicates the highest DC or AC voltage that can be safely applied to the power supply pin without risking damage or malfunction. Verify this limit against the datasheet before designing your circuit to ensure reliable operation under all conditions.

Identifies the conversion architecture, such as ADC, DAC, or DC-DC. This determines the signal path, interface, and performance characteristics. Verify the type matches your system's analog or digital conversion needs before selecting the part.

Manufacturer name as listed in the IHS database. Use this attribute to identify the original component maker when cross-referencing parts across distributors. Verify the manufacturer to ensure authenticity and traceability, especially for critical or regulated applications.

Indicates if the component is designed to withstand ionizing radiation in space, nuclear, or high-energy physics applications. Compare radiation-tolerant vs. radiation-hardened parts for mission-critical designs. Verify the total ionizing dose (TID) and single-event effect (SEE) ratings in the datasheet.

Allowed deviation from the nominal value, expressed as a percentage. Determines precision of resistors, capacitors, and inductors. Choose tighter tolerance for precision circuits, but verify actual performance in the datasheet.

Specifies the maximum data transfer rate the component can handle, typically in bits per second. Compare this value with your system's required throughput to ensure adequate bandwidth. Verify against the datasheet for exact conditions and supported protocols.

Defines the operating temperature range classification for the component, such as commercial, industrial, or automotive. This indicates the environmental conditions the device can withstand. Ensure the grade matches your application's ambient temperature requirements.

Electrical resistance value in ohms, defining opposition to current flow. Critical for current limiting, voltage division, and signal conditioning. Always check tolerance and power rating in the datasheet for reliable circuit operation.

The minimum gate-to-source voltage that makes the device start conducting. Compare this value across parts to ensure your drive circuit can reliably turn the switch on. Always verify against the datasheet for your operating temperature.

Review the complete technical specifications for this electronic component, including electrical ratings, mechanical dimensions, and environmental limits. Verify these parameters against your application requirements and the manufacturer's datasheet to ensure compatibility and reliable operation.

Specifies the metal alloy used for the electrical contact surfaces, affecting conductivity, wear resistance, and corrosion behavior. Compare materials like silver, gold, or palladium for signal integrity and durability. Verify against datasheet for application-specific requirements.

Specifies the nominal operating voltage that must be applied to the component for proper function. Verify this value against your system's power rail and the datasheet's absolute maximum ratings to ensure reliable operation and avoid damage.

Manufacturing technology or process used for the component, such as thin film, thick film, or semiconductor process. Affects performance, stability, and cost. Confirm the technology matches your application requirements and environmental conditions.

Specifies the count of independent functions or channels integrated into a single component package. This helps engineers determine if the part can handle multiple signal paths or operations simultaneously. Verify against the datasheet to ensure the device meets your circuit's functional requirements.

Indicates the maximum voltage the component can withstand or operate at, depending on context. Critical for ensuring the part is not overstressed in your application. Always compare with your circuit's voltage levels and consider transient spikes.

Time required for the device to transition from off state to fully on state. This parameter is critical for timing analysis in power supplies, drivers, and switching circuits. Verify this value against your system's timing budget and switching frequency requirements.

This attribute specifies the thickness of a flat flexible cable (FFC) or flat circuit board (FCB). It is important for ensuring proper insertion into connectors and for mechanical fit in tight enclosures. Engineers must verify this dimension against the connector's specifications to guarantee reliable contact and avoid damage during assembly.

Identifies the manufacturer of the processor, such as Intel, AMD, or ARM. This attribute helps buyers quickly assess compatibility, performance expectations, and supply chain reliability. Always verify the exact brand and model against the datasheet before designing into your system.

The unique part number assigned by the original component manufacturer. Use this to cross-reference datasheets, verify specifications, and ensure the exact component matches your design requirements. Always confirm the number against the manufacturer's official documentation.