TC7117CPL PMIC - Display Drivers by Microchip Technology

Indicates how many analog input channels the device supports. Compare this with your system's sensor or signal requirements. Verify against the datasheet to ensure the device has enough inputs for your application and that input voltage ranges match your signals.

Specifies the binary representation of the digital output signal. This code defines how the device encodes its output state. Engineers compare this to the datasheet to ensure compatibility with the receiving logic and to verify correct decoding of the output data.

Specifies the triac construction or series, such as standard, snubberless, or logic-level. This affects switching performance, gate sensitivity, and commutation capability. Verify the exact type against the datasheet to ensure compatibility with your circuit's voltage, current, and triggering requirements.

Typical current consumed by the component in standby or idle state, measured in milliamperes. This is important for battery-powered or low-power applications. Compare this value with your power budget to ensure the component does not drain excessive current when inactive, affecting overall system efficiency.

This is the on-state resistance between the drain and source terminals of a MOSFET. It affects power dissipation and efficiency. Lower values are preferred for high-current switching. Always check the datasheet for the specified test conditions, as RDS(on) varies with gate voltage and temperature.

Total resistance is the end-to-end resistance of a component, such as a potentiometer or resistor network. It defines the maximum resistance available and is critical for circuit design. Verify this value against the datasheet to ensure proper operation.

Typical switching frequency of a power converter or driver. Compare this value to your application's needs to ensure efficient operation. Verify against the datasheet for exact conditions.

Indicates the construction or configuration of the transformer, such as flyback, forward, or planar. Affects performance, size, and application suitability. Refer to datasheet for detailed specifications and recommended usage.

Specifies the category of accessory or add-on part for electronic components. Use this to filter compatible mounting hardware, connectors, or protective covers. Verify the accessory type against the component datasheet to ensure proper fit and function in your application.

Range of maximum data transfer rates supported by the component, expressed in kilobits per second. This indicates the span of possible speeds the device can handle. Compare this range with your system's required throughput to ensure the component can support the necessary communication bandwidth without data loss.

Specifies the physical medium through which signals travel, such as fiber optic, twisted pair, or coaxial cable. This attribute is critical for ensuring compatibility with your network infrastructure and for meeting performance requirements. Verify the media type against your system's specifications and the component datasheet to avoid signal integrity issues.

Specifies the typical signal loss introduced by the component under standard conditions. Compare this value across similar parts to match your circuit's allowable attenuation. Always verify against the datasheet for frequency and temperature dependencies.

Current that flows through the component when it is in the off-state or reverse-biased. Important for capacitors, diodes, and transistors to minimize power loss and ensure proper isolation. Compare leakage current values to avoid unintended circuit behavior, especially in battery-powered or high-impedance applications. Verify test conditions in the datasheet.

Maximum deviation from ideal linearity in the conversion characteristic. This parameter indicates how accurately the output follows a straight-line response. Compare values across similar converters to assess precision. Verify against the datasheet for guaranteed limits.

Highest data transfer rate the component can reliably support, typically in bits per second. This is critical for serial interfaces, modems, or transceivers. Ensure your application's required data throughput does not exceed this limit to avoid communication errors and performance degradation.

Specifies whether the output current flows from the device into the load or from the load into the device. This matters for sourcing versus sinking configurations. Verify against the datasheet to ensure correct circuit topology and avoid reverse current damage.

Specifies the optical fiber category used in the component, such as single-mode or multimode. This affects bandwidth, distance, and connector compatibility. Verify the fiber type against your network requirements and the datasheet to ensure proper signal transmission and system performance.

Specifies the lowest switching frequency at which the power device can operate reliably. Compare this value with your application's required switching speed to ensure proper performance. Verify against the datasheet's recommended operating conditions.

Specifies the resistance change curve of a potentiometer, such as linear or logarithmic. This affects how the output varies with rotation. Verify the taper type against your circuit requirements and the datasheet to ensure proper volume or control response.

Specifies the plating material on component terminals, affecting solderability, corrosion resistance, and long-term reliability. Compare finishes like tin, gold, or silver for your assembly process and environmental requirements. Verify against datasheet for compliance.

This attribute specifies whether the component uses a multilayer construction, which affects electrical performance and reliability. Compare this parameter when selecting capacitors, inductors, or varistors for high-frequency or high-density circuits. Always verify the layer count and material specifications in the datasheet.

Number of turns in a coil or winding. Affects inductance, transformer ratio, and impedance. Critical for designing transformers, inductors, and magnetic components. Check datasheet for tolerance.

Specifies the filter topology used in the component, such as low-pass, high-pass, band-pass, or notch. This determines the frequency response and attenuation characteristics. Engineers must verify the filter type against the datasheet to ensure it meets the required signal conditioning and interference rejection for the application.

Type of termination on the top side of the component, such as solder pad, lead, or ball. This affects mounting and soldering processes. Buyers should confirm compatibility with their PCB design and assembly methods. Check the datasheet for exact dimensions and materials.

Lists the product categories or classifications assigned to this component, such as connectors, capacitors, or modules. This helps in filtering and comparing similar parts. Review the categories to ensure the component fits your application and to find alternative parts in the same class.

Identifies the company that designed and produced the component. Buyers often filter by manufacturer to ensure brand reliability, quality standards, and supply chain consistency. Verify the manufacturer against the datasheet and official packaging to avoid counterfeit parts.

Indicates the specific product subcategories or classifications within the broader component family. Helps narrow down search results and identify the exact type of component needed for your design. Review the subcategory to ensure compatibility with your application.

Specifies the material of the component's outer casing, such as plastic, metal, or ceramic. This affects durability, thermal performance, and environmental resistance. Verify against datasheet for application-specific requirements like flammability or chemical exposure.

Total number of electrical contacts in the connector, which determines the maximum number of circuits that can be connected. This is a critical parameter for matching the connector to your wire harness requirements. Ensure the contact count aligns with your signal and power needs.

Indicates the locking mechanism used to secure the connector or terminal in place. Choose the appropriate type for your application to ensure reliable mating and vibration resistance. Verify compatibility with the mating part and datasheet specifications.

Bit width of digital data processed by a converter, processor, or memory. Higher bits mean better resolution or precision. Verify against datasheet to match your system's data width and accuracy needs.

Describes special mechanical characteristics for mounting, such as through-hole, surface mount, or specific clips. Ensures compatibility with your PCB layout and assembly process. Confirm before designing the footprint.

Specifies the physical size of the component body, either its length for rectangular parts or diameter for cylindrical ones. This dimension is critical for PCB layout and mechanical fit. Verify against the datasheet to ensure clearance and proper mounting in your enclosure or assembly.

Indicates if the component is designed to withstand ionizing radiation in space, nuclear, or high-energy physics applications. Compare radiation-tolerant vs. radiation-hardened parts for mission-critical designs. Verify the total ionizing dose (TID) and single-event effect (SEE) ratings in the datasheet.

Identifies the conversion architecture, such as ADC, DAC, or DC-DC. This determines the signal path, interface, and performance characteristics. Verify the type matches your system's analog or digital conversion needs before selecting the part.

Physical package or case type of the component, defining its dimensions, mounting style, and thermal characteristics. Common types include SMD, through-hole, BGA, and QFN. Choose the package that fits your PCB layout and assembly process. Verify the exact package code in the datasheet for footprint compatibility.

Specifies the voltage range within which the component operates correctly. Check the datasheet to ensure your power supply meets the minimum and maximum limits, as exceeding them can damage the device or cause malfunction.

Review the complete technical specifications for this electronic component, including electrical ratings, mechanical dimensions, and environmental limits. Verify these parameters against your application requirements and the manufacturer's datasheet to ensure compatibility and reliable operation.

Specifies the maximum power the component can safely dissipate under defined operating conditions. Compare this value with your circuit's power requirements to prevent overheating and ensure reliable operation. Always verify against the datasheet for derating curves and ambient temperature limits.

Position of the terminals on the package, such as dual-in-line, gull-wing, or J-lead. This affects PCB layout, soldering, and thermal performance. Engineers must ensure the terminal position matches the footprint and assembly capabilities of their manufacturing line.

Indicates the maximum continuous wave input power the component can safely handle without damage or excessive distortion. Exceeding this limit may cause failure. Verify this value against your signal power and consider peak-to-average ratio in modulated systems.

Indicates the highest DC or AC voltage that can be safely applied to the power supply pin without risking damage or malfunction. Verify this limit against the datasheet before designing your circuit to ensure reliable operation under all conditions.

Identifies the manufacturer of the processor, such as Intel, AMD, or ARM. This attribute helps buyers quickly assess compatibility, performance expectations, and supply chain reliability. Always verify the exact brand and model against the datasheet before designing into your system.

Specifies the nominal operating voltage that must be applied to the component for proper function. Verify this value against your system's power rail and the datasheet's absolute maximum ratings to ensure reliable operation and avoid damage.

Supported RAM controller types for microprocessors and system-on-chip devices. Indicates which memory standards (DDR, LPDDR, etc.) are integrated. Essential for selecting a processor that matches your memory design and performance requirements.

Manufacturer brand of the electronic component. Helps identify quality, reliability, and sourcing options. Compare brands for performance and availability. Always verify the brand matches your approved vendor list.

The amount of current the device draws from its power supply during normal operation. This is essential for power budget calculations, thermal management, and selecting appropriate power sources. Check datasheet for typical and maximum values under specified conditions.

Specifies the maximum continuous current the component can safely carry under specified conditions. Compare this rating with your circuit's expected load to prevent overheating or failure. Always verify against the datasheet for temperature derating and mounting considerations.

Specifies the maximum data transfer rate the component can handle, typically in bits per second. Compare this value with your system's required throughput to ensure adequate bandwidth. Verify against the datasheet for exact conditions and supported protocols.

Specifies the number of address lines used to access memory or registers. Wider buses address more locations, affecting maximum memory capacity. Verify against the datasheet for compatibility with your microcontroller or processor design.

Select the component category that best matches your application, such as resistor, capacitor, diode, or connector. This classification helps narrow down the correct part family and ensures compatibility with your circuit design. Verify the type against the datasheet to avoid mismatches.

Specifies the manufacturing or processing technique applied to the component, such as stamping, molding, or laser trimming. Buyers compare this to ensure the part meets application-specific reliability and performance requirements. Verify the method against the datasheet or process specification before qualification.

The minimum gate-to-source voltage that makes the device start conducting. Compare this value across parts to ensure your drive circuit can reliably turn the switch on. Always verify against the datasheet for your operating temperature.

The unique part number assigned by the original component manufacturer. Use this to cross-reference datasheets, verify specifications, and ensure the exact component matches your design requirements. Always confirm the number against the manufacturer's official documentation.

Manufacturing technology or process used for the component, such as thin film, thick film, or semiconductor process. Affects performance, stability, and cost. Confirm the technology matches your application requirements and environmental conditions.

Defines the operating temperature range classification for the component, such as commercial, industrial, or automotive. This indicates the environmental conditions the device can withstand. Ensure the grade matches your application's ambient temperature requirements.

Minimum supply voltage is the lowest operating voltage required for the component to function correctly. Operating below this level may cause unreliable performance or failure. Ensure your power supply provides at least this voltage under all load conditions.