ADUM4470CRIZ Digital Isolators by Analog Devices Inc

Harmonized Tariff Schedule code used for customs classification and duty calculation when importing or exporting electronic components. Accurate HTS codes are essential for compliance and cost estimation. Buyers and logistics teams must verify the correct code for the specific component to avoid delays or penalties.

Indicates whether the concentration of Substances of Very High Concern in the component exceeds the regulatory threshold set by REACH. This is a critical compliance flag for EU market access. Buyers must verify this status to ensure legal compliance and avoid supply chain disruptions. Check the latest REACH updates for threshold changes.

The US Export Control Classification Number determines export licensing requirements for electronic components. Verify the current ECCN from the manufacturer or datasheet, as it affects international shipping and compliance with US regulations.

Defines the physical mounting method for the component, such as surface mount, through-hole, or chassis mount. This determines PCB layout, assembly process, and mechanical stability. Buyers must match mounting type to their manufacturing capabilities and application environment. Check the datasheet for recommended footprint and soldering profile.

Indicates the typical duration from order confirmation to shipment from the manufacturer's facility. This helps you plan production schedules and inventory. Verify current lead times with your distributor or supplier, as they may vary based on order quantity, product availability, and market conditions.

Identifies the company that designed and produced the component. Buyers often filter by manufacturer to ensure brand reliability, quality standards, and supply chain consistency. Verify the manufacturer against the datasheet and official packaging to avoid counterfeit parts.

Position of the terminals on the package, such as dual-in-line, gull-wing, or J-lead. This affects PCB layout, soldering, and thermal performance. Engineers must ensure the terminal position matches the footprint and assembly capabilities of their manufacturing line.

Describes the physical configuration of the component's leads or pads, such as through-hole, surface mount, or gull-wing. This affects PCB layout, soldering process, and mechanical fit. Confirm compatibility with your assembly method and footprint.

Specifies the physical length of the component body, typically in millimeters. This dimension is critical for PCB layout and mechanical fit. Verify against the datasheet to ensure proper clearance and alignment in your design.

Shows if the component meets a specific industry standard or reliability level. Buyers should verify this against the datasheet to ensure the part is suitable for their application's environmental and performance requirements.

Typical current drawn from the supply under nominal operating conditions. Compare this value across similar components to estimate power consumption and thermal behavior. Always verify against the datasheet for your specific voltage and load conditions.

Physical package or case type of the component, defining its dimensions, mounting style, and thermal characteristics. Common types include SMD, through-hole, BGA, and QFN. Choose the package that fits your PCB layout and assembly process. Verify the exact package code in the datasheet for footprint compatibility.

A more specific classification within the main product category, such as 'Ceramic Capacitor' under 'Capacitors'. This helps narrow down search results and compare similar components. Use it to filter products with similar characteristics and intended applications.

Manufacturing technology or process used for the component, such as thin film, thick film, or semiconductor process. Affects performance, stability, and cost. Confirm the technology matches your application requirements and environmental conditions.

Indicates the product series or family, grouping components with similar design and specifications. Helps identify compatible parts and compare within a product line. Verify the series against the datasheet to ensure correct application.

Lists the product categories or classifications assigned to this component, such as connectors, capacitors, or modules. This helps in filtering and comparing similar parts. Review the categories to ensure the component fits your application and to find alternative parts in the same class.

Specifies the count of independent functions or channels integrated into a single component package. This helps engineers determine if the part can handle multiple signal paths or operations simultaneously. Verify against the datasheet to ensure the device meets your circuit's functional requirements.

Physical width of the component body, typically in millimeters. Essential for PCB footprint design and mechanical fit. Verify against the datasheet to ensure proper clearance and compatibility with your board layout and enclosure.

Total number of pins or terminals on the component package. Essential for footprint design, PCB layout, and connector mating. Verify against the datasheet to ensure compatibility with your board and assembly process.

Terminal pitch is the center-to-center distance between adjacent leads or pads on a component. It determines PCB layout compatibility and soldering feasibility. Verify against the datasheet to ensure your footprint matches the component's actual lead spacing.

Indicates the specific product subcategories or classifications within the broader component family. Helps narrow down search results and identify the exact type of component needed for your design. Review the subcategory to ensure compatibility with your application.

Minimum common mode transient immunity rating for optocouplers and isolated amplifiers. Indicates the device's ability to withstand rapid voltage changes between input and output without false triggering. Verify against datasheet for reliable operation in noisy industrial environments.

Specifies the highest continuous current the device can supply at its output without exceeding thermal or electrical limits. Compare this value with your load requirements and derating curves. Always verify against the datasheet for your operating conditions.

Indicates whether the component provides galvanic isolation for its power supply, preventing DC or noise from passing between circuits. Essential for safety and noise immunity in industrial, medical, and automotive applications. Check datasheet for isolation voltage rating.

Typical rise and fall time of the output signal, indicating how quickly the device transitions between logic levels. These values affect signal integrity and switching losses. Compare them with your application's required slew rate and check the datasheet for test conditions.

Specifies the highest voltage that can be applied between the collector and emitter terminals without causing breakdown. Critical for selecting transistors in power circuits. Always verify this rating against the datasheet for your operating conditions.

Indicates qualification to Automotive Electronics Council standards, ensuring reliability for automotive applications. Essential for designs requiring high temperature, vibration, and long-term durability. Confirm the specific AEC-Q document (e.g., AEC-Q100) in the datasheet.

Compare the output current relative to the input current in optocouplers and current sensors. This ratio indicates signal transfer efficiency and isolation performance. Verify it against the datasheet for your operating point, as it varies with temperature and forward current.

This attribute specifies the voltage difference between the input thresholds of a receiver, ensuring noise immunity and stable switching. Engineers compare this value to match signal integrity requirements and to prevent false triggering in noisy environments. Always verify against the datasheet for the specific operating conditions.

Stroke indicates the maximum linear travel distance of a moving part, such as a solenoid plunger or actuator shaft. Engineers compare stroke to ensure the component can achieve the required mechanical displacement in their application. Verify the stroke specification against the datasheet to confirm it meets your system's travel requirements.

Specifies the maximum voltage that can be applied between isolated circuits without breakdown. Critical for safety in power supplies, optocouplers, and isolated converters. Verify against datasheet for compliance with required insulation ratings.

Maximum time for a signal to travel from input to output for both low-to-high and high-to-low transitions. Critical for timing analysis in digital circuits. Verify against datasheet for your operating conditions.

Pulse Width Distortion measures the difference in propagation delay between rising and falling edges of a digital signal. It affects timing margins in high-speed interfaces. Engineers compare this value to ensure signal integrity and reliable data transmission. Verify it against the datasheet for your specific operating conditions.

Indicates the certification body that has tested and approved the component for safety or regulatory compliance. Buyers should verify this matches their target market requirements, and engineers should check the datasheet for the specific standards and marks.

This attribute indicates whether the printed circuit board design has been modified from the original version. Buyers should verify this when evaluating product revisions or compatibility with existing designs. Always check the latest datasheet or PCN for details.

Specifies the maximum power the component can safely dissipate under defined operating conditions. Compare this value with your circuit's power requirements to prevent overheating and ensure reliable operation. Always verify against the datasheet for derating curves and ambient temperature limits.

Specifies the highest ambient temperature at which the component can operate reliably. Check this limit against your application's thermal environment to prevent overheating and ensure long-term stability. Always verify with the datasheet for derating curves.

Overall length of the cable assembly from end to end, including connectors if present. This is critical for routing and installation in your system. Ensure the length matches your application requirements to avoid excess slack or tension that could damage the cable or connections.

Indicates the highest power the component can safely dissipate as heat without exceeding its thermal limits. Compare this value with your circuit's expected power loss to ensure reliable operation. Always verify against the datasheet's derating curves for elevated ambient temperatures.

Specifies the maximum continuous current available at the first output of a power supply or converter. Compare this value with your load requirements to ensure sufficient headroom. Verify against the datasheet's derating curves and operating conditions.

Number of input channels available on each side of the device. Useful for multi-channel isolators, drivers, or logic converters. Confirm channel count and configuration in the datasheet to match application requirements.

Indicates if the component is designed to withstand ionizing radiation in space, nuclear, or high-energy physics applications. Compare radiation-tolerant vs. radiation-hardened parts for mission-critical designs. Verify the total ionizing dose (TID) and single-event effect (SEE) ratings in the datasheet.

Indicates how many contacts in a connector are designated for ground connection. This is critical for ensuring proper grounding and signal integrity in electronic assemblies. Compare with circuit requirements and verify against connector datasheet for pinout accuracy.

The unique part number assigned by the original component manufacturer. Use this to cross-reference datasheets, verify specifications, and ensure the exact component matches your design requirements. Always confirm the number against the manufacturer's official documentation.

Specifies the highest continuous current the input pin can safely handle without damage or performance degradation. Compare this limit with your circuit's expected input current to ensure reliable operation. Always verify against the datasheet's absolute maximum ratings for your specific operating conditions.

Indicates the physical form factor of the component, such as through-hole, surface mount, or chassis mount. Buyers compare this to ensure the part fits the PCB layout and mechanical enclosure. Verify the exact shape against the datasheet before design-in.

Specifies the time interval between an input transition and the corresponding output transition. Critical for timing analysis in digital circuits. Verify against datasheet for specific test conditions, supply voltage, and load capacitance.

Specifies the switching regulator control method, such as PWM, PFM, or burst mode. This affects efficiency, noise, and transient response. Engineers should verify the technique against the datasheet to ensure it matches the application's power requirements and EMI constraints.

Specifies the required power supply voltages for the component. Engineers use this to ensure the board's power rails match the device's needs. Verify against the datasheet's recommended operating conditions to avoid undervoltage or overvoltage issues.

Time from when the input signal crosses its threshold until the output begins to turn on. This parameter affects switching speed and power dissipation in high-frequency circuits. Verify it against the datasheet for your specific load and drive conditions.

Specifies the electrical channel configuration, such as unidirectional or bidirectional, for signal or power routing. This attribute is critical for selecting components like multiplexers, isolators, or level shifters. Verify the channel type against your application requirements and the datasheet to ensure correct signal flow and compatibility.

Specifies the typical input voltage level for which the component is designed to operate. Compare this value with your power supply output to ensure compatibility. Always verify against the datasheet for absolute maximum ratings and operating conditions.

Specifies the highest DC or AC voltage that can be safely applied to the input pins without causing damage or malfunction. Verify this limit against your power supply design and derating requirements to ensure reliable operation over the full temperature range.

Specifies the lowest input voltage at which the component operates reliably. Check this against your power supply design to ensure the device starts and functions within its specified range. Critical for DC-DC converters, regulators, and modules.

Time required for a signal to transition from a low to a high level, typically measured between 10% and 90% of the amplitude. Important for digital interfaces, switching regulators, and pulse circuits. Check the datasheet for test conditions and load capacitance.

Specifies the highest rate at which the device can switch on and off reliably. Compare this value with your application's required switching speed to ensure efficient operation and avoid overheating. Always verify against the datasheet for derating conditions.

Specifies the internal circuit topology or arrangement of the component, such as single, dual, or bridge configuration. This attribute helps engineers select the right part for their circuit design. Always verify the exact configuration against the datasheet to ensure compatibility with your application.

Specifies the lowest DC voltage at which the device reliably operates. Compare this with your supply rail and tolerances to ensure proper startup and functionality. Always verify against the datasheet's operating conditions.

Specifies the logical or operational function of the component, such as switching, amplification, or regulation. This attribute helps identify the device's role in a circuit. Verify the function against the datasheet to ensure it matches your application requirements.

Specifies the highest continuous forward current a diode or LED can safely conduct without overheating or degrading. Compare this limit with your circuit's operating current to ensure reliable performance. Always verify against the datasheet's absolute maximum ratings for your specific device.