G3VM-61D1 Solid State Relays by Omron

Indicates whether the component complies with the EU RoHS directive restricting hazardous substances. Buyers should verify this status for regulatory compliance and market access. Check the datasheet or certificate for exact compliance details.

Indicates whether the product contains substances of very high concern as per the REACH regulation. Buyers should verify this for compliance with EU environmental standards, especially when exporting to Europe. Check the manufacturer's declaration or datasheet for accurate SVHC status.

Indicates the floor life of a component before it must be baked prior to soldering. Higher levels require stricter handling and shorter exposure times. Verify the MSL rating in the datasheet to ensure proper storage and assembly conditions.

Indicates how many independent functional sections are integrated into a single component package. This matters when comparing multi-channel devices or resistor networks. Always verify the exact element count against the datasheet to ensure it matches your circuit design requirements.

Capacitance value of the component, typically expressed in farads (pF, nF, µF). This parameter determines energy storage and filtering characteristics. Compare capacitance when selecting capacitors for power supply decoupling, signal coupling, or timing applications. Always check the rated voltage and tolerance in the datasheet.

Specifies the voltage supplied to the load under normal operating conditions. Compare this value with your system's power supply and load requirements to ensure compatibility. Verify against the datasheet for exact tolerances and operating ranges.

Maximum resistance between the switch terminals when the device is fully on. Lower values reduce power loss and heat. Compare this parameter when selecting MOSFETs, IGBTs, or relays for high-current circuits. Always verify against the datasheet for your operating conditions.

Specifies the maximum continuous forward current the component can handle without damage. Compare this rating with your circuit's operating current to ensure reliable performance. Always verify against the datasheet for derating curves and temperature conditions.

Indicates the resistance between insulated conductors or contacts, typically measured in megohms. High values ensure minimal leakage current and safe operation. Check datasheet for minimum acceptable levels under specified test conditions.

Lifecycle status of the part, such as active or obsolete. Indicates availability and long-term support from the manufacturer. Check this before design-in to avoid last-time buys or supply disruptions. Verify with the datasheet or distributor for current status.

Indicates whether the component is manufactured without lead, complying with RoHS and similar regulations. Check this attribute to ensure environmental compliance for your market. Verify against the datasheet for exact material declarations.

Indicates the form of delivery for the component, such as tape and reel, tube, or tray. This affects handling, storage, and assembly processes. Verify the packaging type matches your production requirements and equipment compatibility.

Specifies how the component is attached to the PCB, such as through-hole or surface mount. This affects assembly processes, thermal performance, and mechanical strength. Buyers should verify compatibility with their manufacturing capabilities and design requirements.

Indicates the typical duration from order confirmation to shipment from the manufacturer's facility. This helps you plan production schedules and inventory. Verify current lead times with your distributor or supplier, as they may vary based on order quantity, product availability, and market conditions.

Published indicates the date when the product data was released or updated in the catalog. It helps buyers assess the freshness of the information and whether the component is current or possibly obsolete. Check the datasheet for the latest revisions.

Specifies the lowest ambient temperature at which the component is guaranteed to function within its electrical and mechanical specifications. Verify this limit against the datasheet for your application's thermal environment, especially for automotive or industrial designs.

Specifies the maximum continuous current the component can safely carry under specified conditions. Compare this value with your circuit's expected load to ensure reliable operation. Always verify against the datasheet for temperature derating and mounting considerations.

Physical depth of the component body, measured in millimeters or inches. This dimension affects PCB layout and mechanical fit. Verify against the datasheet for proper clearance in your enclosure or assembly.

Lists the product categories or classifications assigned to this component, such as connectors, capacitors, or modules. This helps in filtering and comparing similar parts. Review the categories to ensure the component fits your application and to find alternative parts in the same class.

Specifies the number of output positions per pole in a switch, such as SPST or DPDT. This determines the switching logic and circuit routing. Verify against the datasheet to ensure the switch matches your application's required contact arrangement and signal path.

Maximum voltage that can be applied to the input without causing damage or malfunction. Exceeding this limit may lead to breakdown or reduced reliability. Always compare with your supply voltage and check the datasheet for absolute maximum ratings.

Classifies the relay by construction or application, such as electromechanical, solid state, or latching. Helps select the right relay for your switching needs. Refer to the datasheet for specific characteristics and ratings.

Identifies the company that designed and produced the component. Buyers often filter by manufacturer to ensure brand reliability, quality standards, and supply chain consistency. Verify the manufacturer against the datasheet and official packaging to avoid counterfeit parts.

Maximum voltage that can be applied between input and output without breakdown. Essential for safety and reliability in isolated power supplies, digital isolators, and optocouplers. Always verify against the datasheet for your application's isolation requirements.

Indicates if the component is designed to withstand ionizing radiation in space, nuclear, or high-energy physics applications. Compare radiation-tolerant vs. radiation-hardened parts for mission-critical designs. Verify the total ionizing dose (TID) and single-event effect (SEE) ratings in the datasheet.

Specifies how the component attaches to the PCB or assembly, such as surface mount, through-hole, or chassis mount. This affects soldering process, mechanical stability, and thermal performance. Verify compatibility with your board layout and assembly capabilities.

Indicates whether the component is lead-free per RoHS or other directives. Buyers use this to verify environmental compliance and avoid restricted substances. Always confirm with the datasheet or certificate of compliance.

Indicates how the component connects to the PCB, such as through-hole, SMD, or press-fit. This affects assembly method, thermal performance, and mechanical strength. Verify compatibility with your board design and soldering process before ordering.

Indicates the certification body that has tested and approved the component for safety or regulatory compliance. Buyers should verify this matches their target market requirements, and engineers should check the datasheet for the specific standards and marks.

Describes the method used to connect the component to the circuit board, such as solder, press-fit, or wire wrap. This affects assembly processes, reliability, and repairability. Check the termination type against your PCB footprint and soldering process to ensure compatibility.

Specifies the highest temperature the semiconductor junction can sustain without damage or degradation. Compare this limit with your operating conditions and thermal management to ensure reliable performance. Verify against the datasheet for derating curves and long-term reliability.

Total number of pins or contacts on the component. This determines the footprint and mating connector requirements. Always match the pin count to your PCB layout and connector specification to ensure proper electrical and mechanical connection.

Current supplied at the output, indicating the load-driving capability of the component. This is crucial for ensuring the component can drive downstream circuitry without overheating or voltage drop. Compare with your load requirements and check the datasheet for maximum ratings.

Total number of electrical contacts in the connector, which determines the maximum number of circuits that can be connected. This is a critical parameter for matching the connector to your wire harness requirements. Ensure the contact count aligns with your signal and power needs.

Specifies the highest continuous current the device can supply at its output without exceeding thermal or electrical limits. Compare this value with your load requirements and derating curves. Always verify against the datasheet for your operating conditions.

Defines the upper limit of ambient temperature for reliable operation without thermal damage or performance degradation. Ensure your system's cooling keeps the component below this threshold. Check the datasheet for derating curves and thermal resistance values.

Physical height of the component, measured from the mounting surface to the topmost point. This dimension is critical for clearance in compact assemblies and for ensuring proper fit within enclosures. Always verify against the datasheet for tolerance and mounting considerations.

Electrical resistance value in ohms, defining opposition to current flow. Critical for current limiting, voltage division, and signal conditioning. Always check tolerance and power rating in the datasheet for reliable circuit operation.

Physical width of the component body, typically in millimeters. Essential for PCB footprint design and mechanical fit. Verify against the datasheet to ensure proper clearance and compatibility with your board layout and enclosure.

Maximum AC voltage that the component can safely withstand under specified conditions. This rating is critical for insulation and safety margins. Always compare it with the operating voltage in your circuit and derate according to the datasheet guidelines.

Specifies the highest voltage the device can deliver at its output under specified conditions. Compare this limit with your application's supply and load requirements to ensure safe operation and avoid overvoltage damage.

Specifies the highest continuous current the input pin can safely handle without damage or performance degradation. Compare this limit with your circuit's expected input current to ensure reliable operation. Always verify against the datasheet's absolute maximum ratings for your specific operating conditions.

Specifies the regulated voltage level available at the output pin under specified load and input conditions. Compare this value with your circuit requirements and verify against the datasheet's tolerance and temperature derating.

Specifies the physical length of the component body, typically in millimeters. This dimension is critical for PCB layout and mechanical fit. Verify against the datasheet to ensure proper clearance and alignment in your design.

Indicates the specific product subcategories or classifications within the broader component family. Helps narrow down search results and identify the exact type of component needed for your design. Review the subcategory to ensure compatibility with your application.

Specifies the electrical configuration of switch contacts, such as SPST, SPDT, or DPDT. This determines how the switch controls the circuit path. Verify the circuit type against your application requirements and the datasheet to ensure correct switching functionality.

Specifies the functional category of an optoelectronic component, such as LED, photodiode, or optocoupler. This attribute helps engineers quickly identify the device's role in a circuit. Always verify the exact type against the datasheet to ensure compatibility with your design's optical and electrical requirements.

Specifies the electrical form of the output signal, such as digital, analog, or open collector. This determines how the component interfaces with your circuit. Verify the output type against your system requirements and the datasheet to ensure proper signal compatibility and avoid logic level mismatches.

Specifies the highest continuous current the device can conduct when fully on. Compare this value with your circuit's peak and average current demands to ensure reliable operation. Always verify against the datasheet's thermal and derating curves for safe operation.

This is the resistance between the main terminals when the device is fully turned on. Lower values reduce power loss and heat. Compare it with the datasheet for your operating current and voltage to ensure efficient switching.

The unique part number assigned by the original component manufacturer. Use this to cross-reference datasheets, verify specifications, and ensure the exact component matches your design requirements. Always confirm the number against the manufacturer's official documentation.

Indicates the product series or family, grouping components with similar design and specifications. Helps identify compatible parts and compare within a product line. Verify the series against the datasheet to ensure correct application.

Specifies the highest ambient temperature at which the component reliably functions. Compare this limit with your application's thermal environment to ensure safe operation. Always verify against the datasheet's derating curves and test conditions, as exceeding this value may cause performance degradation or permanent damage.

Physical package or case type of the component, defining its dimensions, mounting style, and thermal characteristics. Common types include SMD, through-hole, BGA, and QFN. Choose the package that fits your PCB layout and assembly process. Verify the exact package code in the datasheet for footprint compatibility.

Input voltage rating or range for which the component is designed to operate. Exceeding this can damage the device. Check the datasheet for absolute maximum ratings and recommended operating conditions to ensure your supply voltage is within safe limits.

Defines the current drawn at the input terminal under normal operating conditions. Essential for power supply design and thermal management. Check this value against your system's power budget and ensure the input source can deliver it without voltage drop.