SMDA05C-7.TBT TVS - Diodes by Semtech

Specifies the plating material on component terminals, affecting solderability, corrosion resistance, and long-term reliability. Compare finishes like tin, gold, or silver for your assembly process and environmental requirements. Verify against datasheet for compliance.

Capacitance value measured at a specified frequency, often 1 kHz or 1 MHz. Compare this parameter when selecting capacitors for filtering, decoupling, or timing circuits, as capacitance can vary with frequency. Verify the test frequency in the datasheet to ensure consistent performance.

Capacitance value of the component, typically expressed in farads (pF, nF, µF). This parameter determines energy storage and filtering characteristics. Compare capacitance when selecting capacitors for power supply decoupling, signal coupling, or timing applications. Always check the rated voltage and tolerance in the datasheet.

Semiconductor material used in the diode, such as silicon, germanium, or gallium arsenide. Affects forward voltage, speed, and temperature behavior. Choose based on your application's voltage, current, and switching requirements. Verify with datasheet specifications.

Indicates whether the component is designed to protect power supply lines from overvoltage or overcurrent events. Essential for ensuring system reliability in industrial and automotive applications. Confirm the protection level and response time in the datasheet.

Specifies the current level applied during parameter measurement. Compare this value when evaluating test conditions across similar components. Always verify that the test current matches your application's operating point to ensure datasheet parameters are relevant.

Voltage at which the device starts conducting in reverse, marking its safe operating limit. Essential for selecting diodes and transistors for high-voltage applications. Always check this parameter against your circuit's maximum reverse voltage.

Maximum reverse voltage the component can withstand without conducting significant current. For TVS diodes and rectifiers, this is the voltage below which the device remains off. Ensure this voltage is higher than the normal operating voltage to avoid unintended conduction, and check the breakdown voltage in the datasheet.

Maximum repetitive peak reverse voltage the device can withstand without damage. Critical for rectifiers and diodes in AC applications. Ensure this rating exceeds the peak reverse voltage in your circuit to avoid breakdown and premature failure.

Voltage at which the diode begins to conduct in reverse bias, leading to breakdown. Critical for selecting diodes in rectifier and protection circuits. Ensure this voltage exceeds your maximum reverse voltage with margin. Check datasheet for tolerance and temperature effects.

Maximum voltage the component can withstand before breakdown occurs. Essential for ensuring safe operation in high-voltage circuits. Verify this rating against your circuit's worst-case voltage spikes to prevent failure and ensure long-term reliability.

Specifies the voltage level at which a protection device begins to conduct and limit transient overvoltages. Compare this value with the circuit's maximum allowable voltage to ensure adequate protection. Verify against the datasheet for precise clamping characteristics under specified test conditions.

Maximum current the component can withstand during a short pulse event without damage. Compare this rating with your circuit's transient conditions to ensure reliable operation. Verify against the datasheet for pulse duration and duty cycle limits.

Maximum power the component can dissipate during a short pulse, such as a transient voltage surge. Critical for TVS diodes and suppressors to ensure they can handle expected surges without damage. Compare this rating with your system's transient energy and verify pulse duration in the datasheet.

Peak pulse current the component can withstand with a 10/1000µs waveform, commonly used for TVS diodes and surge suppressors. This rating indicates the maximum surge current capability. Compare it with your system's expected transient currents and ensure the component can handle repeated surges without degradation.

Current that flows through the component when it is in the off-state or reverse-biased. Important for capacitors, diodes, and transistors to minimize power loss and ensure proper isolation. Compare leakage current values to avoid unintended circuit behavior, especially in battery-powered or high-impedance applications. Verify test conditions in the datasheet.

Indicates how many independent functional sections are integrated into a single component package. This matters when comparing multi-channel devices or resistor networks. Always verify the exact element count against the datasheet to ensure it matches your circuit design requirements.

Specifies the internal circuit topology or arrangement of the component, such as single, dual, or bridge configuration. This attribute helps engineers select the right part for their circuit design. Always verify the exact configuration against the datasheet to ensure compatibility with your application.

Lifecycle status of the part, such as active or obsolete. Indicates availability and long-term support from the manufacturer. Check this before design-in to avoid last-time buys or supply disruptions. Verify with the datasheet or distributor for current status.

Indicates whether the component is manufactured without lead, complying with RoHS and similar regulations. Check this attribute to ensure environmental compliance for your market. Verify against the datasheet for exact material declarations.

Specifies how the component is attached to the PCB, such as through-hole or surface mount. This affects assembly processes, thermal performance, and mechanical strength. Buyers should verify compatibility with their manufacturing capabilities and design requirements.

Indicates the typical duration from order confirmation to shipment from the manufacturer's facility. This helps you plan production schedules and inventory. Verify current lead times with your distributor or supplier, as they may vary based on order quantity, product availability, and market conditions.

Indicates the form of delivery for the component, such as tape and reel, tube, or tray. This affects handling, storage, and assembly processes. Verify the packaging type matches your production requirements and equipment compatibility.

Position of the terminals on the package, such as dual-in-line, gull-wing, or J-lead. This affects PCB layout, soldering, and thermal performance. Engineers must ensure the terminal position matches the footprint and assembly capabilities of their manufacturing line.

Maximum temperature during reflow soldering that the component can withstand. This is critical for solder joint reliability and preventing damage. Verify that the peak reflow temperature is compatible with your soldering profile and the component's moisture sensitivity level.

Describes the physical configuration of the component's leads or pads, such as through-hole, surface mount, or gull-wing. This affects PCB layout, soldering process, and mechanical fit. Confirm compatibility with your assembly method and footprint.

Physical package or case type of the component, defining its dimensions, mounting style, and thermal characteristics. Common types include SMD, through-hole, BGA, and QFN. Choose the package that fits your PCB layout and assembly process. Verify the exact package code in the datasheet for footprint compatibility.

Lists the product categories or classifications assigned to this component, such as connectors, capacitors, or modules. This helps in filtering and comparing similar parts. Review the categories to ensure the component fits your application and to find alternative parts in the same class.

Select the component category that best matches your application, such as resistor, capacitor, diode, or connector. This classification helps narrow down the correct part family and ensures compatibility with your circuit design. Verify the type against the datasheet to avoid mismatches.

Indicates the specific product subcategories or classifications within the broader component family. Helps narrow down search results and identify the exact type of component needed for your design. Review the subcategory to ensure compatibility with your application.

A more specific classification within the main product category, such as 'Ceramic Capacitor' under 'Capacitors'. This helps narrow down search results and compare similar components. Use it to filter products with similar characteristics and intended applications.

Manufacturing technology or process used for the component, such as thin film, thick film, or semiconductor process. Affects performance, stability, and cost. Confirm the technology matches your application requirements and environmental conditions.

Harmonized Tariff Schedule code used for customs classification of electronic components. Helps determine duties and regulatory requirements. Buyers should confirm the code with a customs broker for accurate shipping.

This is the maximum reverse voltage the device can withstand without entering breakdown. It defines the safe operating limit for TVS diodes and similar protection components. Engineers compare this value to the circuit's normal operating voltage to ensure adequate protection margin. Always verify against the datasheet for your specific application.

Total number of pins or contacts on the component. This determines the footprint and mating connector requirements. Always match the pin count to your PCB layout and connector specification to ensure proper electrical and mechanical connection.

Specifies how the component attaches to the PCB or assembly, such as surface mount, through-hole, or chassis mount. This affects soldering process, mechanical stability, and thermal performance. Verify compatibility with your board layout and assembly capabilities.

Indicates whether the component is lead-free per RoHS or other directives. Buyers use this to verify environmental compliance and avoid restricted substances. Always confirm with the datasheet or certificate of compliance.

Indicates the total number of electrical connection points on the component, such as pins or pads. This is critical for PCB footprint design and assembly. Verify it matches the package specification to ensure proper soldering and connectivity.

Total number of pins or terminals on the component package. Essential for footprint design, PCB layout, and connector mating. Verify against the datasheet to ensure compatibility with your board and assembly process.

Specifies the physical length of the component body, typically in millimeters. This dimension is critical for PCB layout and mechanical fit. Verify against the datasheet to ensure proper clearance and alignment in your design.

Specify the typical end-use scenarios for this electronic component, such as consumer electronics, automotive, industrial, or telecommunications. This helps engineers quickly assess suitability for their design. Verify against the datasheet's application section.

Defines the maximum continuous voltage that can be applied across the component during normal operation without degradation. This is critical for capacitors, connectors, and insulation ratings. Check the datasheet to confirm the safe operating range and any environmental derating.

Specifies whether the component or signal has a defined positive and negative orientation, such as for diodes, electrolytic capacitors, or connectors. Incorrect polarity can cause failure or unsafe operation. Always check the datasheet and board markings before installation.

Maximum power the component can safely dissipate as heat without damage. Exceeding this may cause failure. Check datasheet for thermal resistance and derating curves under your operating conditions.

Lists any extra characteristics or capabilities beyond the standard specifications, such as built-in protection, special mounting options, or enhanced performance. Review these features to ensure they meet your application's specific needs and compare them across similar parts.

Specifies the ambient temperature range within which the component reliably functions. Compare this with your application's thermal environment to ensure proper operation. Always verify against the datasheet for derating curves and maximum ratings.

Standardized package code from JEDEC-95 for semiconductor devices. This code identifies the physical package outline, pin configuration, and mounting style. Buyers and engineers use it to ensure mechanical compatibility with PCB footprints and assembly processes. Verify the exact code against the datasheet to avoid mismatches in design.

Identifies the company that designed and produced the component. Buyers often filter by manufacturer to ensure brand reliability, quality standards, and supply chain consistency. Verify the manufacturer against the datasheet and official packaging to avoid counterfeit parts.

Physical depth of the component body, measured in millimeters or inches. This dimension affects PCB layout and mechanical fit. Verify against the datasheet for proper clearance in your enclosure or assembly.

Identifies the core product family without package, grade, or option suffixes. Use this to compare equivalent components across manufacturers and to locate the primary datasheet. Verify the full ordering code against the manufacturer's specification before design-in.

Indicates how many independent signal paths can transmit data in both directions simultaneously. Essential for bus transceivers, level shifters, and multiplexers. Verify against the datasheet to ensure the channel count matches your system's required data lines.

The unique part number assigned by the original component manufacturer. Use this to cross-reference datasheets, verify specifications, and ensure the exact component matches your design requirements. Always confirm the number against the manufacturer's official documentation.

Indicates the product series or family, grouping components with similar design and specifications. Helps identify compatible parts and compare within a product line. Verify the series against the datasheet to ensure correct application.

This code indicates the terminal finish material per JESD-609 standard. It helps identify the plating type for soldering compatibility and environmental compliance. Check the datasheet for the exact code and its meaning.

Indicates whether the component complies with the EU RoHS directive restricting hazardous substances. Buyers should verify this status for regulatory compliance and market access. Check the datasheet or certificate for exact compliance details.

Indicates whether the product contains substances of very high concern as per the REACH regulation. Buyers should verify this for compliance with EU environmental standards, especially when exporting to Europe. Check the manufacturer's declaration or datasheet for accurate SVHC status.

Indicates the floor life of a component before it must be baked prior to soldering. Higher levels require stricter handling and shorter exposure times. Verify the MSL rating in the datasheet to ensure proper storage and assembly conditions.

JEDEC standard code that defines the package outline and dimensions. Use it to verify physical compatibility and footprint before PCB design. Compare with the datasheet to ensure the component meets your assembly and manufacturing requirements.

Export Control Classification Number assigned by the U.S. Commerce Department. It determines export licensing requirements for electronic components. Verify the ECCN against the manufacturer's datasheet or export compliance documentation before shipping internationally.