M29W128GL70ZA6E Memory by Micron Technology

Indicates whether the component complies with the EU RoHS directive restricting hazardous substances. Buyers should verify this status for regulatory compliance and market access. Check the datasheet or certificate for exact compliance details.

Indicates the floor life of a component before it must be baked prior to soldering. Higher levels require stricter handling and shorter exposure times. Verify the MSL rating in the datasheet to ensure proper storage and assembly conditions.

This code indicates the terminal finish material per JESD-609 standard. It helps identify the plating type for soldering compatibility and environmental compliance. Check the datasheet for the exact code and its meaning.

Export Control Classification Number assigned by the U.S. Commerce Department. It determines export licensing requirements for electronic components. Verify the ECCN against the manufacturer's datasheet or export compliance documentation before shipping internationally.

Harmonized Tariff Schedule of the United States code for customs classification. Essential for import/export documentation and duty calculation. Verify the correct code with a trade specialist to avoid customs delays.

Specifies the required power supply voltages for the component. Engineers use this to ensure the board's power rails match the device's needs. Verify against the datasheet's recommended operating conditions to avoid undervoltage or overvoltage issues.

Specifies the plating material on component terminals, affecting solderability, corrosion resistance, and long-term reliability. Compare finishes like tin, gold, or silver for your assembly process and environmental requirements. Verify against datasheet for compliance.

Specifies the range of DC or AC input voltage the component requires for proper operation. Engineers compare this to the system power rail to ensure compatibility. Always verify against the datasheet's absolute maximum ratings to prevent damage.

Specifies an alternative memory bus width configuration supported by the device. This is relevant for memory modules, microcontrollers, and FPGAs. Compare this attribute to understand flexibility in interfacing with different memory types or to optimize bandwidth versus pin count.

Total storage capacity of the memory chip, typically expressed in bits or bytes. Compare densities to match your application's code and data requirements. Verify against the datasheet to ensure sufficient headroom for firmware and runtime variables.

Indicates the total storage capacity of the memory device, typically in bits or bytes. Buyers use this to match firmware or data storage requirements. Confirm the exact organization and density in the datasheet before design-in.

Maximum vertical dimension from the seating plane to the top of the component body. Critical for PCB clearance and enclosure fit. Verify against the datasheet when designing mechanical constraints or checking compatibility with mating parts.

Indicates the form of delivery for the component, such as tape and reel, tube, or tray. This affects handling, storage, and assembly processes. Verify the packaging type matches your production requirements and equipment compatibility.

Published indicates the date when the product data was released or updated in the catalog. It helps buyers assess the freshness of the information and whether the component is current or possibly obsolete. Check the datasheet for the latest revisions.

Shows whether the component complies with the EU REACH regulation. Essential for legal market access in Europe. Check the manufacturer's latest statement to confirm that no substances of very high concern are present above the threshold.

Specifies how the component is attached to the PCB, such as through-hole or surface mount. This affects assembly processes, thermal performance, and mechanical strength. Buyers should verify compatibility with their manufacturing capabilities and design requirements.

Lifecycle status of the part, such as active or obsolete. Indicates availability and long-term support from the manufacturer. Check this before design-in to avoid last-time buys or supply disruptions. Verify with the datasheet or distributor for current status.

Lists the product categories or classifications assigned to this component, such as connectors, capacitors, or modules. This helps in filtering and comparing similar parts. Review the categories to ensure the component fits your application and to find alternative parts in the same class.

Maximum temperature during reflow soldering that the component can withstand. This is critical for solder joint reliability and preventing damage. Verify that the peak reflow temperature is compatible with your soldering profile and the component's moisture sensitivity level.

Specifies the ambient temperature range within which the component reliably functions. Compare this with your application's thermal environment to ensure proper operation. Always verify against the datasheet for derating curves and maximum ratings.

Specifies the nominal operating voltage that must be applied to the component for proper function. Verify this value against your system's power rail and the datasheet's absolute maximum ratings to ensure reliable operation and avoid damage.

Specifies the count of independent functions or channels integrated into a single component package. This helps engineers determine if the part can handle multiple signal paths or operations simultaneously. Verify against the datasheet to ensure the device meets your circuit's functional requirements.

Mounting type: surface mount or through-hole. Surface mount components are placed directly on the PCB, saving space and enabling automated assembly. Through-hole components offer stronger mechanical bonds. Verify the mounting style matches your PCB design and assembly process.

Maximum time the component can be exposed to the peak reflow temperature during soldering. Exceeding this duration may cause damage or degrade reliability. Ensure your soldering profile stays within this limit and check the datasheet for exact conditions.

Indicates if the component is designed to withstand ionizing radiation in space, nuclear, or high-energy physics applications. Compare radiation-tolerant vs. radiation-hardened parts for mission-critical designs. Verify the total ionizing dose (TID) and single-event effect (SEE) ratings in the datasheet.

Physical width of the component body, typically in millimeters. Essential for PCB footprint design and mechanical fit. Verify against the datasheet to ensure proper clearance and compatibility with your board layout and enclosure.

Total number of pins or contacts on the component. This determines the footprint and mating connector requirements. Always match the pin count to your PCB layout and connector specification to ensure proper electrical and mechanical connection.

Indicates the total number of electrical connection points on the component, such as pins or pads. This is critical for PCB footprint design and assembly. Verify it matches the package specification to ensure proper soldering and connectivity.

Total number of pins or terminals on the component package. Essential for footprint design, PCB layout, and connector mating. Verify against the datasheet to ensure compatibility with your board and assembly process.

Indicates whether the component is lead-free per RoHS or other directives. Buyers use this to verify environmental compliance and avoid restricted substances. Always confirm with the datasheet or certificate of compliance.

Position of the terminals on the package, such as dual-in-line, gull-wing, or J-lead. This affects PCB layout, soldering, and thermal performance. Engineers must ensure the terminal position matches the footprint and assembly capabilities of their manufacturing line.

Specifies the physical length of the component body, typically in millimeters. This dimension is critical for PCB layout and mechanical fit. Verify against the datasheet to ensure proper clearance and alignment in your design.

Defines the underlying technology used for data storage, such as SRAM, DRAM, or Flash. Determines volatility, speed, and endurance. Choose based on your application's need for persistence and access speed.

Typical current drawn from the supply under nominal operating conditions. Compare this value across similar components to estimate power consumption and thermal behavior. Always verify against the datasheet for your specific voltage and load conditions.

Export Control Classification Number assigned by the U.S. government. Determines whether the component requires an export license. Essential for international trade compliance. Verify the ECCN with the manufacturer or supplier before shipping to avoid legal issues.

Terminal pitch is the center-to-center distance between adjacent leads or pads on a component. It determines PCB layout compatibility and soldering feasibility. Verify against the datasheet to ensure your footprint matches the component's actual lead spacing.

Standardized interface for flash memory devices, enabling host controllers to identify and program them. It ensures compatibility across manufacturers. Engineers use this to verify that the memory can be accessed with standard commands. Check the datasheet for supported commands and timing.

Harmonized Tariff Schedule code used for customs classification of electronic components. Helps determine duties and regulatory requirements. Buyers should confirm the code with a customs broker for accurate shipping.

Data polling is a method used in memory devices to verify that a write operation has completed. It involves reading a specific data bit until it matches the expected value. Engineers compare this feature to ensure reliable programming and to avoid premature read operations.

Specifies the protocol or bus standard used to connect the component to external memory. Common types include SPI, I2C, parallel, and DDR. Verify compatibility with your host controller and memory device to ensure proper communication and data transfer rates.

Indicates the specific product subcategories or classifications within the broader component family. Helps narrow down search results and identify the exact type of component needed for your design. Review the subcategory to ensure compatibility with your application.

Indicates whether the device is ready to accept commands or busy processing. Check this status pin or register before initiating operations to avoid communication errors. Verify timing and logic levels in the datasheet for reliable system integration.

Interface for sending commands to a device, typically for configuration or control. It defines the protocol and command set. Engineers compare this to ensure the device can be integrated with their system. Verify the command set and response timing in the datasheet.

Indicates whether the component operates in synchronous or asynchronous mode. This affects timing, clocking, and data transfer protocols. Verify the mode against your system requirements and the datasheet to ensure proper integration and performance.

A status bit that toggles state to indicate a change in device condition, such as program completion or error. It is used for polling or interrupt generation. Engineers monitor this bit to track device status. Check the datasheet for its behavior and timing.

Specifies the internal organization of the memory device, such as DRAM, SRAM, or Flash. This affects how data is accessed and stored. Verify the format against your application requirements and the datasheet to ensure compatibility with your system's memory controller.

Specifies the number of bits transferred simultaneously between the memory device and the controller. Wider buses enable higher data throughput. Verify this parameter against the datasheet to ensure compatibility with your system's bus architecture and expected performance.

Specifies the number of sectors and their individual size for rotary switches or encoders. This attribute helps engineers determine the number of positions and the angular spacing between them. Verify against the datasheet to ensure compatibility with your control panel or circuit design.

Specifies the duration needed to program a single word or a page in non-volatile memory. Compare this timing when selecting EEPROM or flash devices for write-intensive applications. Verify against the datasheet to ensure your system meets the required write throughput.

Maximum time required to read or write data in memory devices. Lower values indicate faster performance. Critical for timing analysis in digital systems. Verify against the datasheet to ensure it meets your system's speed requirements.

Manufacturing technology or process used for the component, such as thin film, thick film, or semiconductor process. Affects performance, stability, and cost. Confirm the technology matches your application requirements and environmental conditions.

Maximum current drawn by the component when in standby or sleep mode. Lower values extend battery life in portable designs. Verify against datasheet conditions, as standby current can vary with supply voltage and temperature.

Identifies the company that designed and produced the component. Buyers often filter by manufacturer to ensure brand reliability, quality standards, and supply chain consistency. Verify the manufacturer against the datasheet and official packaging to avoid counterfeit parts.

Indicates the maximum voltage the component can withstand or operate at, depending on context. Critical for ensuring the part is not overstressed in your application. Always compare with your circuit's voltage levels and consider transient spikes.

Specifies the smallest erasable block size in memory devices. Compare sector sizes when selecting flash or EEPROM for firmware updates or data storage. Verify against the datasheet to ensure compatibility with your file system and wear-leveling requirements.

Physical package or case type of the component, defining its dimensions, mounting style, and thermal characteristics. Common types include SMD, through-hole, BGA, and QFN. Choose the package that fits your PCB layout and assembly process. Verify the exact package code in the datasheet for footprint compatibility.

Identifies the core product family without package, grade, or option suffixes. Use this to compare equivalent components across manufacturers and to locate the primary datasheet. Verify the full ordering code against the manufacturer's specification before design-in.

Specifies the internal arrangement of memory cells, typically expressed as words by bits. This affects how data is accessed and stored. Engineers compare this to ensure compatibility with their system's bus width and addressing scheme. Always verify against the datasheet for exact configuration.

The unique part number assigned by the original component manufacturer. Use this to cross-reference datasheets, verify specifications, and ensure the exact component matches your design requirements. Always confirm the number against the manufacturer's official documentation.

Memory page size determines the granularity of read and write operations in flash or EEPROM devices. Compare this value with your application's data block size to ensure efficient programming and erase cycles. Always verify against the datasheet for exact page boundaries.