OPA364AID Linear - Amplifiers - Instrumentation, Operational Amplifiers, Buffer Amplifiers by Texas Instruments

Specifies the plating material on component terminals, affecting solderability, corrosion resistance, and long-term reliability. Compare finishes like tin, gold, or silver for your assembly process and environmental requirements. Verify against datasheet for compliance.

Specifies the required power supply voltages for the component. Engineers use this to ensure the board's power rails match the device's needs. Verify against the datasheet's recommended operating conditions to avoid undervoltage or overvoltage issues.

Measures how well the amplifier rejects variations in its power supply voltage, expressed in dB. A higher PSRR indicates better output stability against supply noise. Essential for audio, precision measurement, and automotive applications. Always compare PSRR values across frequencies in the datasheet.

Specifies the DC current flowing into the input terminals of an op-amp or comparator. It affects offset voltage and precision in high-impedance circuits. Verify against the datasheet for your operating temperature and supply voltage.

Specifies the allowable supply voltage range for single or dual supply operation. Critical for ensuring the device operates within its rated limits. Verify against the datasheet for absolute maximum ratings and recommended operating conditions.

Specifies how many independent signal paths or outputs the component provides. Compare this value with your circuit requirements to ensure each channel can be used separately. Verify the channel configuration in the datasheet, as some devices may share pins or have internal connections.

Specifies the amplifier topology or functional class, such as operational, instrumentation, or differential. This determines circuit behavior, gain characteristics, and suitable applications. Verify the exact type against the datasheet to ensure compatibility with your design requirements.

DC voltage difference between the inverting and non-inverting inputs required to make the output zero. This parameter affects precision and DC accuracy. Compare it when designing amplifiers for sensor or measurement applications. Verify the maximum value over temperature in the datasheet.

Specifies the highest voltage that can be safely applied to input/output pins without damaging the device. Check this limit against your logic levels and supply rails to ensure reliable operation and avoid overvoltage stress.

Specifies the functional mode of the component, such as continuous, discontinuous, or burst mode. This affects efficiency and performance in your circuit. Verify the mode against your application requirements and the datasheet to ensure proper operation.

Specifies the number of signal lines or channels supported by the component. Compare this value with your circuit's required data or power paths. Always verify against the datasheet to ensure the part matches your design's channel count and pinout.

This pin or terminal accepts a control signal that loads or presets a counter, register, or similar digital circuit. Engineers compare this input's logic threshold and timing requirements to ensure proper synchronization with the system clock and data bus.

Specifies whether the counter increments or decrements with each input pulse. Choose the direction that matches your application's counting logic. Verify this setting against the datasheet to ensure correct operation in your system.

Total ionizing dose tolerance for radiation-hardened components. Indicates maximum cumulative radiation exposure before performance degrades. Critical for aerospace, nuclear, and medical applications. Verify against datasheet for mission-specific radiation requirements.

Input current is the current flowing into the input terminal under specified conditions. It affects power consumption and loading on the driving source. Compare this value with the output drive capability of preceding stages to ensure proper signal levels and avoid excessive power dissipation.

Clamping voltage is the voltage level at which a protection device, such as a TVS diode or clamp circuit, begins to conduct and limit the voltage. It is critical for surge protection; engineers select components with a clamping voltage below the maximum rating of the protected circuit.

This parameter indicates the highest positive voltage that can be applied to the input pin without causing damage or malfunction. Engineers must ensure the input signal never exceeds this rating, considering transient spikes and supply variations, to maintain reliability and prevent latch-up.

Indicates the frequency at which the open-loop gain of an amplifier falls to unity. Compare this value when selecting op-amps for high-speed signal processing. Verify against the datasheet to ensure adequate bandwidth for your application's required gain.

Indicates whether the component complies with the EU RoHS directive restricting hazardous substances. Buyers should verify this status for regulatory compliance and market access. Check the datasheet or certificate for exact compliance details.

Indicates whether the product contains substances of very high concern as per the REACH regulation. Buyers should verify this for compliance with EU environmental standards, especially when exporting to Europe. Check the manufacturer's declaration or datasheet for accurate SVHC status.

This code indicates the terminal finish material per JESD-609 standard. It helps identify the plating type for soldering compatibility and environmental compliance. Check the datasheet for the exact code and its meaning.

Indicates the floor life of a component before it must be baked prior to soldering. Higher levels require stricter handling and shorter exposure times. Verify the MSL rating in the datasheet to ensure proper storage and assembly conditions.

Export Control Classification Number assigned by the U.S. Commerce Department. It determines export licensing requirements for electronic components. Verify the ECCN against the manufacturer's datasheet or export compliance documentation before shipping internationally.

Lifecycle status of the part, such as active or obsolete. Indicates availability and long-term support from the manufacturer. Check this before design-in to avoid last-time buys or supply disruptions. Verify with the datasheet or distributor for current status.

Indicates whether the component is manufactured without lead, complying with RoHS and similar regulations. Check this attribute to ensure environmental compliance for your market. Verify against the datasheet for exact material declarations.

Indicates the form of delivery for the component, such as tape and reel, tube, or tray. This affects handling, storage, and assembly processes. Verify the packaging type matches your production requirements and equipment compatibility.

Current stage in the product's lifecycle, such as Active, Obsolete, or End of Life. This indicates availability and long-term supply risk. Check this before designing in a part to ensure it will be available for your product's production lifetime.

Specifies how the component is attached to the PCB, such as through-hole or surface mount. This affects assembly processes, thermal performance, and mechanical strength. Buyers should verify compatibility with their manufacturing capabilities and design requirements.

Indicates the typical duration from order confirmation to shipment from the manufacturer's facility. This helps you plan production schedules and inventory. Verify current lead times with your distributor or supplier, as they may vary based on order quantity, product availability, and market conditions.

Lists the product categories or classifications assigned to this component, such as connectors, capacitors, or modules. This helps in filtering and comparing similar parts. Review the categories to ensure the component fits your application and to find alternative parts in the same class.

Position of the terminals on the package, such as dual-in-line, gull-wing, or J-lead. This affects PCB layout, soldering, and thermal performance. Engineers must ensure the terminal position matches the footprint and assembly capabilities of their manufacturing line.

Maximum temperature during reflow soldering that the component can withstand. This is critical for solder joint reliability and preventing damage. Verify that the peak reflow temperature is compatible with your soldering profile and the component's moisture sensitivity level.

Describes the physical configuration of the component's leads or pads, such as through-hole, surface mount, or gull-wing. This affects PCB layout, soldering process, and mechanical fit. Confirm compatibility with your assembly method and footprint.

Specifies the ambient temperature range within which the component reliably functions. Compare this with your application's thermal environment to ensure proper operation. Always verify against the datasheet for derating curves and maximum ratings.

Manufacturing technology or process used for the component, such as thin film, thick film, or semiconductor process. Affects performance, stability, and cost. Confirm the technology matches your application requirements and environmental conditions.

Identifies the company that designed and produced the component. Buyers often filter by manufacturer to ensure brand reliability, quality standards, and supply chain consistency. Verify the manufacturer against the datasheet and official packaging to avoid counterfeit parts.

Physical width of the component body, typically in millimeters. Essential for PCB footprint design and mechanical fit. Verify against the datasheet to ensure proper clearance and compatibility with your board layout and enclosure.

Physical height of the component, measured from the mounting surface to the topmost point. This dimension is critical for clearance in compact assemblies and for ensuring proper fit within enclosures. Always verify against the datasheet for tolerance and mounting considerations.

Specifies the electrical form of the output signal, such as digital, analog, or open collector. This determines how the component interfaces with your circuit. Verify the output type against your system requirements and the datasheet to ensure proper signal compatibility and avoid logic level mismatches.

Physical package or case type of the component, defining its dimensions, mounting style, and thermal characteristics. Common types include SMD, through-hole, BGA, and QFN. Choose the package that fits your PCB layout and assembly process. Verify the exact package code in the datasheet for footprint compatibility.

A more specific classification within the main product category, such as 'Ceramic Capacitor' under 'Capacitors'. This helps narrow down search results and compare similar components. Use it to filter products with similar characteristics and intended applications.

Indicates the specific product subcategories or classifications within the broader component family. Helps narrow down search results and identify the exact type of component needed for your design. Review the subcategory to ensure compatibility with your application.

Typical current drawn from the supply under nominal operating conditions. Compare this value across similar components to estimate power consumption and thermal behavior. Always verify against the datasheet for your specific voltage and load conditions.

Slew rate indicates how fast an amplifier's output voltage can change. It affects signal fidelity in high-frequency applications. Compare values when selecting op-amps or drivers, and verify against the datasheet's typical test conditions.

The DC voltage difference between the two input terminals of an operational amplifier or comparator. It indicates how closely the device matches ideal behavior. Compare this value across devices to ensure precision in your circuit design, and verify it against the datasheet for your operating conditions.

Indicates the frequency range over which the component operates effectively. Compare bandwidth when selecting amplifiers, filters, or data converters. Verify the specified bandwidth against your signal frequency requirements and the datasheet's test conditions to ensure optimal performance.

Specifies the count of independent functions or channels integrated into a single component package. This helps engineers determine if the part can handle multiple signal paths or operations simultaneously. Verify against the datasheet to ensure the device meets your circuit's functional requirements.

Mounting type: surface mount or through-hole. Surface mount components are placed directly on the PCB, saving space and enabling automated assembly. Through-hole components offer stronger mechanical bonds. Verify the mounting style matches your PCB design and assembly process.

Indicates if the component is designed to withstand ionizing radiation in space, nuclear, or high-energy physics applications. Compare radiation-tolerant vs. radiation-hardened parts for mission-critical designs. Verify the total ionizing dose (TID) and single-event effect (SEE) ratings in the datasheet.

Indicates whether the component is lead-free per RoHS or other directives. Buyers use this to verify environmental compliance and avoid restricted substances. Always confirm with the datasheet or certificate of compliance.

Specifies the voltage range within which the component operates correctly. Check the datasheet to ensure your power supply meets the minimum and maximum limits, as exceeding them can damage the device or cause malfunction.

Total number of pins or contacts on the component. This determines the footprint and mating connector requirements. Always match the pin count to your PCB layout and connector specification to ensure proper electrical and mechanical connection.

Indicates the total number of electrical connection points on the component, such as pins or pads. This is critical for PCB footprint design and assembly. Verify it matches the package specification to ensure proper soldering and connectivity.

Total number of pins or terminals on the component package. Essential for footprint design, PCB layout, and connector mating. Verify against the datasheet to ensure compatibility with your board and assembly process.

Specifies the physical length of the component body, typically in millimeters. This dimension is critical for PCB layout and mechanical fit. Verify against the datasheet to ensure proper clearance and alignment in your design.

Indicates how effectively an operational amplifier or differential amplifier suppresses signals common to both inputs. Higher values mean better rejection of noise and interference. Compare this parameter across devices when designing precision analog circuits, and verify it against the datasheet for your operating conditions.

The amount of current the device draws from its power supply during normal operation. This is essential for power budget calculations, thermal management, and selecting appropriate power sources. Check datasheet for typical and maximum values under specified conditions.

Specifies the nominal operating voltage that must be applied to the component for proper function. Verify this value against your system's power rail and the datasheet's absolute maximum ratings to ensure reliable operation and avoid damage.

Specifies the maximum current each output channel can source or sink continuously. Compare this value with your load requirements to ensure the driver or amplifier can handle the current without overheating or damage. Always verify against the datasheet for absolute maximum ratings and derating curves.

Maximum allowable AC supply voltage that the component can withstand without damage or performance degradation. This rating is critical for power supplies, relays, and optocouplers. Ensure your circuit's AC voltage does not exceed this limit, and check the datasheet for frequency dependence and safety margins.

Identifies the core product family without package, grade, or option suffixes. Use this to compare equivalent components across manufacturers and to locate the primary datasheet. Verify the full ordering code against the manufacturer's specification before design-in.

The unique part number assigned by the original component manufacturer. Use this to cross-reference datasheets, verify specifications, and ensure the exact component matches your design requirements. Always confirm the number against the manufacturer's official documentation.