MAX191ACWG+ Data Acquisition - Analog to Digital Converters (ADC) by Maxim Integrated

This code indicates the terminal finish material per JESD-609 standard. It helps identify the plating type for soldering compatibility and environmental compliance. Check the datasheet for the exact code and its meaning.

Indicates whether the component complies with the EU RoHS directive restricting hazardous substances. Buyers should verify this status for regulatory compliance and market access. Check the datasheet or certificate for exact compliance details.

Indicates the floor life of a component before it must be baked prior to soldering. Higher levels require stricter handling and shorter exposure times. Verify the MSL rating in the datasheet to ensure proper storage and assembly conditions.

Export Control Classification Number assigned by the U.S. Commerce Department. It determines export licensing requirements for electronic components. Verify the ECCN against the manufacturer's datasheet or export compliance documentation before shipping internationally.

Specifies the internal circuit topology or arrangement of the component, such as single, dual, or bridge configuration. This attribute helps engineers select the right part for their circuit design. Always verify the exact configuration against the datasheet to ensure compatibility with your application.

Indicates the required power source, such as AC or DC, for the component. Engineers compare this to ensure compatibility with the system's power architecture. Verify the supply type against the datasheet to avoid incorrect power connections.

Specifies the sampling technique in an ADC, affecting how the analog input is captured and held during conversion. Engineers compare this to ensure the ADC meets the required signal acquisition speed and accuracy for their application.

Specifies how many independent signal paths or outputs the component provides. Compare this value with your circuit requirements to ensure each channel can be used separately. Verify the channel configuration in the datasheet, as some devices may share pins or have internal connections.

Specifies the maximum duration a component can withstand at the peak reflow temperature during soldering. Critical for evaluating solder joint reliability and preventing thermal damage. Verify against the datasheet's recommended soldering profile to ensure proper assembly.

Check if the component needs both positive and negative supply rails. This affects power design and compatibility with your system. Verify the required voltages and tolerances in the datasheet before selecting the part.

Indicates the maximum deviation of an actual code step from the ideal one-step size in an ADC or DAC. Compare this parameter across converters to assess linearity and potential distortion. Verify the specified value in the datasheet for your operating conditions.

This ratio defines the relationship between the sample-and-hold circuit and the analog-to-digital converter in the signal path. It affects conversion accuracy and timing. Verify this parameter against the datasheet when designing precision data acquisition systems.

The nominal negative supply voltage required for dual-supply operation. This is critical for circuits using both positive and negative rails, such as operational amplifiers. Ensure your power supply provides this voltage within the specified tolerance.

Specifies the minimum and maximum input voltage or current the device can accept for normal operation. Verify this range against your power supply or signal source to ensure compatibility and prevent damage. Critical for power modules, converters, and sensor interfaces.

Specifies the number of signal lines or channels supported by the component. Compare this value with your circuit's required data or power paths. Always verify against the datasheet to ensure the part matches your design's channel count and pinout.

Indicates the lowest dual supply voltage (positive and negative rails) at which the component operates correctly. This is critical for op-amps, ADCs, and other analog devices. Ensure your power rails meet this minimum to avoid malfunction or degraded performance.

Specifies the highest voltage that can be applied between the positive and negative supply rails of a dual-supply device. Exceeding this limit may damage the component. Verify this parameter against the datasheet for proper power supply design and reliability.

Indicates the total count of programmable logic elements or cells in the FPGA or CPLD. This parameter determines the device's logic capacity and complexity. Compare this value with your design requirements to ensure sufficient resources. Always verify against the datasheet for exact specifications.

Input capacitance is the effective capacitance seen at the input terminal of a component. It affects signal integrity, impedance matching, and switching behavior. Engineers compare this value to ensure proper circuit operation and to avoid unintended resonance or filtering. Verify against the datasheet for accurate modeling.

Indicates how many times per second the device captures an analog signal. Higher rates capture faster changes but increase data volume. Verify against your application's bandwidth needs and the datasheet's maximum rating.

Highlight any distinctive capabilities or design aspects that set this component apart, such as integrated protection, low power consumption, or high-speed switching. Compare these features against your application requirements and verify them in the datasheet to ensure compatibility.

Indicates how many serial input/output interfaces the component provides. Compare this when selecting microcontrollers, FPGAs, or interface ICs to ensure enough UART, SPI, or I2C channels for your design. Verify against the datasheet pinout and peripheral list.

Lifecycle status of the part, such as active or obsolete. Indicates availability and long-term support from the manufacturer. Check this before design-in to avoid last-time buys or supply disruptions. Verify with the datasheet or distributor for current status.

Indicates whether the component is manufactured without lead, complying with RoHS and similar regulations. Check this attribute to ensure environmental compliance for your market. Verify against the datasheet for exact material declarations.

Indicates the form of delivery for the component, such as tape and reel, tube, or tray. This affects handling, storage, and assembly processes. Verify the packaging type matches your production requirements and equipment compatibility.

Specifies how the component is attached to the PCB, such as through-hole or surface mount. This affects assembly processes, thermal performance, and mechanical strength. Buyers should verify compatibility with their manufacturing capabilities and design requirements.

Published indicates the date when the product data was released or updated in the catalog. It helps buyers assess the freshness of the information and whether the component is current or possibly obsolete. Check the datasheet for the latest revisions.

Indicates the typical duration from order confirmation to shipment from the manufacturer's facility. This helps you plan production schedules and inventory. Verify current lead times with your distributor or supplier, as they may vary based on order quantity, product availability, and market conditions.

Indicates the maximum deviation of the ADC or DAC transfer function from an ideal straight line. Compare this value to ensure conversion accuracy for precision measurement and control applications. Verify against the datasheet's specified conditions, such as temperature and supply voltage.

Lists the product categories or classifications assigned to this component, such as connectors, capacitors, or modules. This helps in filtering and comparing similar parts. Review the categories to ensure the component fits your application and to find alternative parts in the same class.

Maximum temperature during reflow soldering that the component can withstand. This is critical for solder joint reliability and preventing damage. Verify that the peak reflow temperature is compatible with your soldering profile and the component's moisture sensitivity level.

Describes the physical configuration of the component's leads or pads, such as through-hole, surface mount, or gull-wing. This affects PCB layout, soldering process, and mechanical fit. Confirm compatibility with your assembly method and footprint.

Specifies whether the component or signal has a defined positive and negative orientation, such as for diodes, electrolytic capacitors, or connectors. Incorrect polarity can cause failure or unsafe operation. Always check the datasheet and board markings before installation.

Specifies the nominal operating voltage that must be applied to the component for proper function. Verify this value against your system's power rail and the datasheet's absolute maximum ratings to ensure reliable operation and avoid damage.

Manufacturing technology or process used for the component, such as thin film, thick film, or semiconductor process. Affects performance, stability, and cost. Confirm the technology matches your application requirements and environmental conditions.

Indicates the specific product subcategories or classifications within the broader component family. Helps narrow down search results and identify the exact type of component needed for your design. Review the subcategory to ensure compatibility with your application.

A more specific classification within the main product category, such as 'Ceramic Capacitor' under 'Capacitors'. This helps narrow down search results and compare similar components. Use it to filter products with similar characteristics and intended applications.

Identifies the conversion architecture, such as ADC, DAC, or DC-DC. This determines the signal path, interface, and performance characteristics. Verify the type matches your system's analog or digital conversion needs before selecting the part.

Resolution defines the smallest detectable change in a sensor's output or measurement. For electronic components, it determines precision and accuracy. Engineers compare resolution to ensure the component meets system requirements. Always verify the datasheet for exact resolution specifications under operating conditions.

Indicates how many analog-to-digital or digital-to-analog conversions the device completes per second. Compare this rate with your system's sampling requirements to ensure real-time data acquisition. Verify the specified rate under the datasheet's operating conditions, as it may vary with clock frequency and supply voltage.

Specifies the lowest DC input voltage at which the component reliably operates. Compare this value with your system's power rail tolerances and the device's recommended operating conditions to ensure stable performance across all load and temperature ranges.

Physical package or case type of the component, defining its dimensions, mounting style, and thermal characteristics. Common types include SMD, through-hole, BGA, and QFN. Choose the package that fits your PCB layout and assembly process. Verify the exact package code in the datasheet for footprint compatibility.

Specifies the ambient temperature range within which the component reliably functions. Compare this with your application's thermal environment to ensure proper operation. Always verify against the datasheet for derating curves and maximum ratings.

Specifies the communication protocol or interface type used by the component, such as I2C, SPI, UART, or USB. This determines how the device connects to a microcontroller or system. Verify compatibility with your host controller and bus voltage levels before design-in.

Identifies the company that designed and produced the component. Buyers often filter by manufacturer to ensure brand reliability, quality standards, and supply chain consistency. Verify the manufacturer against the datasheet and official packaging to avoid counterfeit parts.

Specifies the acceptable range for the analog supply voltage input. This rail powers internal analog circuitry and affects accuracy and noise performance. Ensure your power design stays within this range to maintain specified operation.

Specifies the count of independent functions or channels integrated into a single component package. This helps engineers determine if the part can handle multiple signal paths or operations simultaneously. Verify against the datasheet to ensure the device meets your circuit's functional requirements.

Indicates the total number of electrical connection points on the component, such as pins or pads. This is critical for PCB footprint design and assembly. Verify it matches the package specification to ensure proper soldering and connectivity.

Total number of pins or terminals on the component package. Essential for footprint design, PCB layout, and connector mating. Verify against the datasheet to ensure compatibility with your board and assembly process.

Specifies the voltage range within which the component operates correctly. Check the datasheet to ensure your power supply meets the minimum and maximum limits, as exceeding them can damage the device or cause malfunction.

Maximum power the component can safely dissipate as heat without exceeding its thermal limits. Compare this rating with your application's expected power loss to ensure reliable operation. Always verify against the datasheet's derating curves and ambient temperature conditions.

Total number of pins or contacts on the component. This determines the footprint and mating connector requirements. Always match the pin count to your PCB layout and connector specification to ensure proper electrical and mechanical connection.

Bit width of digital data processed by a converter, processor, or memory. Higher bits mean better resolution or precision. Verify against datasheet to match your system's data width and accuracy needs.

Indicates the highest DC or AC voltage that can be safely applied to the power supply pin without risking damage or malfunction. Verify this limit against the datasheet before designing your circuit to ensure reliable operation under all conditions.

Specifies the metal coating applied to the contact surfaces of connectors, switches, or relays. This finish affects conductivity, corrosion resistance, and durability. Engineers should verify the plating material and thickness against the datasheet to ensure reliable performance in the intended environment.

Indicates if the component is designed to withstand ionizing radiation in space, nuclear, or high-energy physics applications. Compare radiation-tolerant vs. radiation-hardened parts for mission-critical designs. Verify the total ionizing dose (TID) and single-event effect (SEE) ratings in the datasheet.

Physical width of the component body, typically in millimeters. Essential for PCB footprint design and mechanical fit. Verify against the datasheet to ensure proper clearance and compatibility with your board layout and enclosure.

Specifies how the component attaches to the PCB or assembly, such as surface mount, through-hole, or chassis mount. This affects soldering process, mechanical stability, and thermal performance. Verify compatibility with your board layout and assembly capabilities.

Indicates whether the component is lead-free per RoHS or other directives. Buyers use this to verify environmental compliance and avoid restricted substances. Always confirm with the datasheet or certificate of compliance.

Number of analog signal samples taken per second by an ADC or digital sensor. Determines maximum signal frequency that can be accurately captured. Verify against datasheet for your application's bandwidth needs.

This attribute specifies the voltage difference between the input thresholds of a receiver, ensuring noise immunity and stable switching. Engineers compare this value to match signal integrity requirements and to prevent false triggering in noisy environments. Always verify against the datasheet for the specific operating conditions.

Identifies the core product family without package, grade, or option suffixes. Use this to compare equivalent components across manufacturers and to locate the primary datasheet. Verify the full ordering code against the manufacturer's specification before design-in.

Maximum power the component can safely dissipate as heat without damage. Exceeding this may cause failure. Check datasheet for thermal resistance and derating curves under your operating conditions.

The unique part number assigned by the original component manufacturer. Use this to cross-reference datasheets, verify specifications, and ensure the exact component matches your design requirements. Always confirm the number against the manufacturer's official documentation.

Maximum vertical dimension from the seating plane to the top of the component body. Critical for PCB clearance and enclosure fit. Verify against the datasheet when designing mechanical constraints or checking compatibility with mating parts.