ADG936BRUZ-R RF Switches by Analog Devices Inc

This code indicates the terminal finish material per JESD-609 standard. It helps identify the plating type for soldering compatibility and environmental compliance. Check the datasheet for the exact code and its meaning.

Indicates the floor life of a component before it must be baked prior to soldering. Higher levels require stricter handling and shorter exposure times. Verify the MSL rating in the datasheet to ensure proper storage and assembly conditions.

Indicates whether the component complies with the EU RoHS directive restricting hazardous substances. Buyers should verify this status for regulatory compliance and market access. Check the datasheet or certificate for exact compliance details.

Indicates whether the product contains substances of very high concern as per the REACH regulation. Buyers should verify this for compliance with EU environmental standards, especially when exporting to Europe. Check the manufacturer's declaration or datasheet for accurate SVHC status.

Harmonized Tariff Schedule of the United States code for customs classification. Essential for import/export documentation and duty calculation. Verify the correct code with a trade specialist to avoid customs delays.

Export Control Classification Number assigned by the U.S. Commerce Department. It determines export licensing requirements for electronic components. Verify the ECCN against the manufacturer's datasheet or export compliance documentation before shipping internationally.

Measures the time from when the turn-off command is applied to when the device actually begins to switch off. This delay affects switching losses and timing in power circuits. Engineers compare this parameter to ensure proper synchronization and to minimize power dissipation during high-frequency operation.

Time from when the input signal crosses its threshold until the output begins to turn on. This parameter affects switching speed and power dissipation in high-frequency circuits. Verify it against the datasheet for your specific load and drive conditions.

Specifies how many independent signal paths or outputs the component provides. Compare this value with your circuit requirements to ensure each channel can be used separately. Verify the channel configuration in the datasheet, as some devices may share pins or have internal connections.

Minimum supply voltage for proper operation. Check the datasheet to ensure your power rail meets this threshold. Critical for low-voltage designs and battery-powered applications. Compare across parts to avoid undervoltage failures.

Specifies the nominal resistance between isolated circuits when the component is off. Higher values indicate better isolation and lower leakage. Verify this parameter against the datasheet for applications requiring high voltage or safety isolation.

Specifies the range of DC or AC input voltage the component requires for proper operation. Engineers compare this to the system power rail to ensure compatibility. Always verify against the datasheet's absolute maximum ratings to prevent damage.

Specifies the internal circuit architecture of the power converter, such as flyback, forward, or buck. This determines efficiency, isolation, and component stress. Engineers must verify topology against the datasheet to ensure it matches the intended application and operating conditions.

Lifecycle status of the part, such as active or obsolete. Indicates availability and long-term support from the manufacturer. Check this before design-in to avoid last-time buys or supply disruptions. Verify with the datasheet or distributor for current status.

Shows whether the component complies with the EU REACH regulation. Essential for legal market access in Europe. Check the manufacturer's latest statement to confirm that no substances of very high concern are present above the threshold.

Export Control Classification Number assigned by the U.S. government. Determines whether the component requires an export license. Essential for international trade compliance. Verify the ECCN with the manufacturer or supplier before shipping to avoid legal issues.

Indicates the form of delivery for the component, such as tape and reel, tube, or tray. This affects handling, storage, and assembly processes. Verify the packaging type matches your production requirements and equipment compatibility.

Indicates whether the component is manufactured without lead, complying with RoHS and similar regulations. Check this attribute to ensure environmental compliance for your market. Verify against the datasheet for exact material declarations.

Indicates the typical duration from order confirmation to shipment from the manufacturer's facility. This helps you plan production schedules and inventory. Verify current lead times with your distributor or supplier, as they may vary based on order quantity, product availability, and market conditions.

Specifies the ambient temperature range within which the component reliably functions. Compare this with your application's thermal environment to ensure proper operation. Always verify against the datasheet for derating curves and maximum ratings.

Identifies the company that designed and produced the component. Buyers often filter by manufacturer to ensure brand reliability, quality standards, and supply chain consistency. Verify the manufacturer against the datasheet and official packaging to avoid counterfeit parts.

Position of the terminals on the package, such as dual-in-line, gull-wing, or J-lead. This affects PCB layout, soldering, and thermal performance. Engineers must ensure the terminal position matches the footprint and assembly capabilities of their manufacturing line.

Maximum temperature during reflow soldering that the component can withstand. This is critical for solder joint reliability and preventing damage. Verify that the peak reflow temperature is compatible with your soldering profile and the component's moisture sensitivity level.

Describes the physical configuration of the component's leads or pads, such as through-hole, surface mount, or gull-wing. This affects PCB layout, soldering process, and mechanical fit. Confirm compatibility with your assembly method and footprint.

Manufacturing technology or process used for the component, such as thin film, thick film, or semiconductor process. Affects performance, stability, and cost. Confirm the technology matches your application requirements and environmental conditions.

Shows if the component meets a specific industry standard or reliability level. Buyers should verify this against the datasheet to ensure the part is suitable for their application's environmental and performance requirements.

Terminal pitch is the center-to-center distance between adjacent leads or pads on a component. It determines PCB layout compatibility and soldering feasibility. Verify against the datasheet to ensure your footprint matches the component's actual lead spacing.

Specifies the communication protocol or interface type used by the component, such as I2C, SPI, UART, or USB. This determines how the device connects to a microcontroller or system. Verify compatibility with your host controller and bus voltage levels before design-in.

Physical package or case type of the component, defining its dimensions, mounting style, and thermal characteristics. Common types include SMD, through-hole, BGA, and QFN. Choose the package that fits your PCB layout and assembly process. Verify the exact package code in the datasheet for footprint compatibility.

Physical height of the component, measured from the mounting surface to the topmost point. This dimension is critical for clearance in compact assemblies and for ensuring proper fit within enclosures. Always verify against the datasheet for tolerance and mounting considerations.

Operating frequency of the component, typically the clock or switching frequency. This determines the speed of operation and affects power dissipation and signal integrity. Verify the frequency range against your application's requirements and the datasheet specifications.

Specifies the opposition to alternating current in a component, typically for RF or high-speed signal paths. Compare values to ensure proper impedance matching and signal integrity. Verify against the datasheet for your application frequency.

Current stage in the product's lifecycle, such as Active, Obsolete, or End of Life. This indicates availability and long-term supply risk. Check this before designing in a part to ensure it will be available for your product's production lifetime.

Indicates whether the component is lead-free per RoHS or other directives. Buyers use this to verify environmental compliance and avoid restricted substances. Always confirm with the datasheet or certificate of compliance.

Maximum time the component can be exposed to the peak reflow temperature during soldering. Exceeding this duration may cause damage or degrade reliability. Ensure your soldering profile stays within this limit and check the datasheet for exact conditions.

Specifies the metal coating applied to the contact surfaces of connectors, switches, or relays. This finish affects conductivity, corrosion resistance, and durability. Engineers should verify the plating material and thickness against the datasheet to ensure reliable performance in the intended environment.

Indicates the total number of electrical connection points on the component, such as pins or pads. This is critical for PCB footprint design and assembly. Verify it matches the package specification to ensure proper soldering and connectivity.

Total number of pins or contacts on the component. This determines the footprint and mating connector requirements. Always match the pin count to your PCB layout and connector specification to ensure proper electrical and mechanical connection.

Total number of pins or terminals on the component package. Essential for footprint design, PCB layout, and connector mating. Verify against the datasheet to ensure compatibility with your board and assembly process.

Specifies the nominal operating voltage that must be applied to the component for proper function. Verify this value against your system's power rail and the datasheet's absolute maximum ratings to ensure reliable operation and avoid damage.

Specifies how the component attaches to the PCB or assembly, such as surface mount, through-hole, or chassis mount. This affects soldering process, mechanical stability, and thermal performance. Verify compatibility with your board layout and assembly capabilities.

Specifies the count of independent functions or channels integrated into a single component package. This helps engineers determine if the part can handle multiple signal paths or operations simultaneously. Verify against the datasheet to ensure the device meets your circuit's functional requirements.

Specifies the voltage range within which the component operates correctly. Check the datasheet to ensure your power supply meets the minimum and maximum limits, as exceeding them can damage the device or cause malfunction.

Bit width of digital data processed by a converter, processor, or memory. Higher bits mean better resolution or precision. Verify against datasheet to match your system's data width and accuracy needs.

Specifies the number of output positions per pole in a switch, such as SPST or DPDT. This determines the switching logic and circuit routing. Verify against the datasheet to ensure the switch matches your application's required contact arrangement and signal path.

Physical width of the component body, typically in millimeters. Essential for PCB footprint design and mechanical fit. Verify against the datasheet to ensure proper clearance and compatibility with your board layout and enclosure.

Lists the product categories or classifications assigned to this component, such as connectors, capacitors, or modules. This helps in filtering and comparing similar parts. Review the categories to ensure the component fits your application and to find alternative parts in the same class.

Specifies the physical length of the component body, typically in millimeters. This dimension is critical for PCB layout and mechanical fit. Verify against the datasheet to ensure proper clearance and alignment in your design.

Maximum power the component can safely dissipate as heat without exceeding its thermal limits. Compare this rating with your application's expected power loss to ensure reliable operation. Always verify against the datasheet's derating curves and ambient temperature conditions.

Maximum time required for the device to transition from on-state to off-state after removal of the drive signal. Critical for switching power supplies and motor drives. Verify against datasheet timing diagrams to ensure it meets your circuit's dead-time and frequency requirements.

Indicates the specific product subcategories or classifications within the broader component family. Helps narrow down search results and identify the exact type of component needed for your design. Review the subcategory to ensure compatibility with your application.

Specifies the frequency at which the component's electrical performance is measured during production testing. Compare this value with the datasheet to ensure the test conditions match your application's operating frequency, as performance can vary significantly with frequency.

Insertion loss measures signal power reduction when a component is placed in a transmission line. Lower values indicate better performance. Compare this parameter across similar parts and verify it against the datasheet for your operating frequency.

Indicates the frequency range where the component's gain or response remains within 3 dB of its nominal value. Engineers compare this to ensure signal fidelity in amplifiers, filters, and communication circuits. Verify against the datasheet for your operating frequency.

Indicates the frequency range over which the component operates effectively. Compare bandwidth when selecting amplifiers, filters, or data converters. Verify the specified bandwidth against your signal frequency requirements and the datasheet's test conditions to ensure optimal performance.

Specifies the minimum and maximum operating frequencies for which the component is designed. Compare this range with your application's signal or switching frequency to ensure proper performance. Always verify against the datasheet for exact limits and conditions.

Identifies the core product family without package, grade, or option suffixes. Use this to compare equivalent components across manufacturers and to locate the primary datasheet. Verify the full ordering code against the manufacturer's specification before design-in.

P1dB indicates the output power level where amplifier gain compresses by 1 dB. It defines linear operating range and is critical for RF and microwave components. Compare with datasheet to ensure sufficient headroom for your signal levels.

Input third-order intercept point, a key linearity figure for RF components. Higher IIP3 indicates better handling of strong signals with less intermodulation distortion. Compare values when selecting amplifiers, mixers, or receivers for demanding RF applications, and verify against the datasheet.

Insertion loss measures signal power reduction caused by placing a component in a transmission path. Lower values indicate better performance. Compare this parameter across similar components to ensure signal integrity in your application, and verify it against the datasheet for your operating frequency.

Maximum power the component can safely dissipate as heat without damage. Exceeding this may cause failure. Check datasheet for thermal resistance and derating curves under your operating conditions.

Specifies the electrical configuration of switch contacts, such as SPST, SPDT, or DPDT. This determines how the switch controls the circuit path. Verify the circuit type against your application requirements and the datasheet to ensure correct switching functionality.

Specifies the isolation rating or type between input and output circuits. Critical for safety and signal integrity in power supplies, isolators, and optocouplers. Verify against datasheet for compliance with your application's voltage and safety requirements.

Specifies the RF application or standard the component is designed for, such as Bluetooth, Wi-Fi, or Zigbee. Buyers use this to ensure compatibility with their wireless protocol and frequency band. Verify the exact RF type against the datasheet to avoid mismatches in your design.

Specifies the longest interval from applying the control signal until the device conducts or switches on. Compare this value with your timing requirements, especially in power supplies or switching circuits. Verify against the datasheet under specified test conditions, as it affects efficiency and transient response.

The unique part number assigned by the original component manufacturer. Use this to cross-reference datasheets, verify specifications, and ensure the exact component matches your design requirements. Always confirm the number against the manufacturer's official documentation.