2007870-1 Backplane Connectors - Specialized by TE Connectivity

Lifecycle status of the part, such as active or obsolete. Indicates availability and long-term support from the manufacturer. Check this before design-in to avoid last-time buys or supply disruptions. Verify with the datasheet or distributor for current status.

Identifies the company that designed and produced the component. Buyers often filter by manufacturer to ensure brand reliability, quality standards, and supply chain consistency. Verify the manufacturer against the datasheet and official packaging to avoid counterfeit parts.

UL flammability rating of the material used in the component, indicating its resistance to ignition and flame spread. This is important for safety compliance in end products. Check the rating against your application's required safety standards and environmental conditions.

Lists the product categories or classifications assigned to this component, such as connectors, capacitors, or modules. This helps in filtering and comparing similar parts. Review the categories to ensure the component fits your application and to find alternative parts in the same class.

Indicates the physical mounting orientation of the connector relative to the PCB or mating direction. Engineers compare this to ensure proper alignment in the assembly. Verify against the datasheet for correct placement and mating.

Specifies how the component is attached to the PCB, such as through-hole or surface mount. This affects assembly processes, thermal performance, and mechanical strength. Buyers should verify compatibility with their manufacturing capabilities and design requirements.

Indicates how many contact positions in a connector housing are actually populated with contacts. Compare this to the total number of positions to understand which contacts are present. Verify against the datasheet or part marking to ensure the connector meets your wiring requirements.

Indicates compliance with the European End-of-Life Vehicle directive, restricting hazardous substances in automotive components. Verify this attribute when sourcing parts for vehicles to ensure environmental and regulatory compliance. Check the datasheet or certificate for specific ELV status.

Specifies the base metal layer applied beneath the final plating finish. This underplate affects solderability, corrosion resistance, and long-term reliability of terminations. Engineers should verify this material against the datasheet when designing for harsh environments or high-temperature soldering processes.

Specifies the typical circuit role or topology for which the component is designed, such as buck converter, audio amplifier, or signal conditioning. Engineers use this to quickly match parts to their application. Verify against the datasheet's recommended operating conditions and example circuits.

Export Control Classification Number assigned by the U.S. government. Determines whether the component requires an export license. Essential for international trade compliance. Verify the ECCN with the manufacturer or supplier before shipping to avoid legal issues.

Indicates the form of delivery for the component, such as tape and reel, tube, or tray. This affects handling, storage, and assembly processes. Verify the packaging type matches your production requirements and equipment compatibility.

Specifies the metal coating applied to the contact surfaces of connectors, switches, or relays. This finish affects conductivity, corrosion resistance, and durability. Engineers should verify the plating material and thickness against the datasheet to ensure reliable performance in the intended environment.

Shows whether the component complies with the EU REACH regulation. Essential for legal market access in Europe. Check the manufacturer's latest statement to confirm that no substances of very high concern are present above the threshold.

Specifies the thickness of the metal plating on connector contacts or terminals. Thicker plating generally improves corrosion resistance and durability. Verify this value against the datasheet when selecting parts for harsh environments or high mating cycle applications.

Current stage in the product's lifecycle, such as Active, Obsolete, or End of Life. This indicates availability and long-term supply risk. Check this before designing in a part to ensure it will be available for your product's production lifetime.

Specifies the material of the component's outer casing, such as plastic, metal, or ceramic. This affects durability, thermal performance, and environmental resistance. Verify against datasheet for application-specific requirements like flammability or chemical exposure.

Published indicates the date when the product data was released or updated in the catalog. It helps buyers assess the freshness of the information and whether the component is current or possibly obsolete. Check the datasheet for the latest revisions.

Indicates the typical duration from order confirmation to shipment from the manufacturer's facility. This helps you plan production schedules and inventory. Verify current lead times with your distributor or supplier, as they may vary based on order quantity, product availability, and market conditions.

Indicates the specific product subcategories or classifications within the broader component family. Helps narrow down search results and identify the exact type of component needed for your design. Review the subcategory to ensure compatibility with your application.

Specifies the connector series or family, such as USB, RJ45, or D-Sub. This determines mechanical compatibility, pin layout, and mating standards. Verify against the datasheet to ensure the connector matches your board design and mating counterpart.

Specifies the lowest ambient temperature at which the component is guaranteed to function within its electrical and mechanical specifications. Verify this limit against the datasheet for your application's thermal environment, especially for automotive or industrial designs.

Specifies the diameter of the mounting hole on the component or PCB footprint. This dimension is critical for ensuring proper fit of leads, pins, or hardware. Verify against the datasheet to avoid assembly issues.

Describes the method used to connect the component to the circuit board, such as solder, press-fit, or wire wrap. This affects assembly processes, reliability, and repairability. Check the termination type against your PCB footprint and soldering process to ensure compatibility.

Specifies the highest continuous current the component can safely carry under specified conditions. Compare this rating with your circuit's expected load to prevent overheating or failure. Always verify against the datasheet's derating curves and ambient temperature limits.

Specifies the maximum data transfer rate the component can handle, typically in bits per second. Compare this value with your system's required throughput to ensure adequate bandwidth. Verify against the datasheet for exact conditions and supported protocols.

Specifies the thickness of the printed circuit board for which the component is designed. This dimension affects mechanical fit and thermal performance. Verify it against the PCB stack-up and assembly requirements to ensure proper mounting and reliability.

Indicates the product series or family, grouping components with similar design and specifications. Helps identify compatible parts and compare within a product line. Verify the series against the datasheet to ensure correct application.

Specifies the opposition to alternating current in a component, typically for RF or high-speed signal paths. Compare values to ensure proper impedance matching and signal integrity. Verify against the datasheet for your application frequency.

Specifies the center-to-center distance between rows of contacts in a multi-row connector. This dimension is critical for PCB layout and mating with standard headers. Verify against the datasheet to ensure compatibility with your board design and connector housing.

The center-to-center distance between adjacent contacts in a connector. Pitch determines the connector's size and PCB footprint requirements. Smaller pitch allows higher density but may require more precise manufacturing. Verify pitch matches your board layout and mating connector to ensure reliable connections.

Specifies the ambient temperature range within which the component reliably functions. Compare this with your application's thermal environment to ensure proper operation. Always verify against the datasheet for derating curves and maximum ratings.

Indicates whether the connector has a shroud or shield around its contacts. Shrouded connectors provide mechanical protection and prevent accidental shorting. This affects mating alignment and durability. Check the datasheet for shroud dimensions and material to ensure proper fit in your enclosure.

Specifies the total height when multiple components are stacked vertically. This dimension is critical for board clearance and mechanical fit in dense assemblies. Verify against the datasheet to ensure proper enclosure and mating with adjacent parts.

Specifies the length of the contact tail that extends beyond the insulator or mounting surface. This dimension affects PCB hole depth and solder joint reliability. Verify against the datasheet for proper mating and mechanical fit.

Total number of contact positions in the connector. This determines the maximum number of electrical connections possible. Compare with your circuit requirements and verify against the datasheet to ensure the connector matches your pin count and layout.

Specifies the highest ambient temperature at which the component reliably functions. Compare this limit with your application's thermal environment to ensure safe operation. Always verify against the datasheet's derating curves and test conditions, as exceeding this value may cause performance degradation or permanent damage.

Specifies the physical length of the component body, typically in millimeters. This dimension is critical for PCB layout and mechanical fit. Verify against the datasheet to ensure proper clearance and alignment in your design.

Physical width of the component body, typically in millimeters. Essential for PCB footprint design and mechanical fit. Verify against the datasheet to ensure proper clearance and compatibility with your board layout and enclosure.

Specifies the visual color of the component body or housing. Useful for identifying parts in inventory or matching design aesthetics. Verify against the datasheet or physical sample, as color may vary between manufacturers and batches.

Specifies how the component attaches to the PCB or assembly, such as surface mount, through-hole, or chassis mount. This affects soldering process, mechanical stability, and thermal performance. Verify compatibility with your board layout and assembly capabilities.

Indicates the flammability classification of the insulating material used in the component, typically following UL 94 standards. This rating helps engineers assess fire safety and compliance with regulatory requirements. Check the datasheet for the specific test method and thickness conditions.

Indicates the color of the component's outer housing, which may aid in visual identification and inventory management. Verify the color against the manufacturer's datasheet or product photos, as it does not affect electrical performance but may be important for assembly or aesthetic requirements.

Specifies the component's physical orientation when mounted on the PCB, such as vertical, horizontal, or angled. This affects layout, clearance, and thermal management. Verify against the datasheet for proper assembly and to avoid interference with neighboring parts.

Indicates whether the component can be physically stacked with identical units to save board space or increase capacity. Check the datasheet for stacking orientation, mechanical tolerances, and any derating requirements when used in stacked configurations.

Indicates the mechanical method used to align connector halves during mating, such as keying or polarization. This ensures correct orientation and prevents misconnection. Verify the alignment type against the datasheet to ensure compatibility with your mating connector and application requirements.

Specifies the voltage range within which the component operates correctly. Check the datasheet to ensure your power supply meets the minimum and maximum limits, as exceeding them can damage the device or cause malfunction.

Specifies the plating thickness on the contact surface, which affects durability, corrosion resistance, and mating cycle life. Compare values across similar connectors to ensure reliable performance in your application, and verify against the datasheet for exact specifications.

Specifies the sequence of contact closure and opening in a switch or relay. This matters for circuits where power must be applied before signal or vice versa. Verify the contact timing against the datasheet to ensure safe operation.

Specifies the plating material on the contact surface, affecting conductivity, corrosion resistance, and durability. Compare finishes like gold, tin, or silver for mating cycle requirements and environmental exposure. Verify the exact finish and thickness in the datasheet to ensure reliable performance in your application.

Indicates whether the component can be sealed to protect against moisture, dust, or other environmental factors. Relevant for connectors, switches, and enclosures used in harsh environments. Verify sealing capability with the manufacturer's specifications.

Specifies the maximum continuous current the component can safely carry under specified conditions. Compare this value with your circuit's expected load to ensure reliable operation. Always verify against the datasheet for temperature derating and mounting considerations.

Specifies the physical shape or configuration of the electrical contact, such as pin, socket, blade, or crimp. This affects mating compatibility and reliability. Verify the contact style against the connector series and datasheet to ensure proper fit and performance in your application.

Indicates whether the component supports differential signaling for robust data transmission. Check this attribute when selecting interfaces like LVDS, RS-485, or Ethernet PHYs to ensure signal integrity and noise immunity in your design.

Specifies the count of contact columns in the connector grid. This affects the pin layout and mating compatibility. Verify against the datasheet to ensure the connector matches your PCB footprint and intended signal routing.

Specifies the number of twisted or differential signal pairs supported by the component. This is essential for high-speed data interfaces like Ethernet or LVDS. Confirm the pair count in the datasheet to match your system's signal routing and bandwidth requirements.

Specifies how many rows of contacts the connector has, typically one, two, or more. This affects the connector's footprint, pin count, and mating force. Choose the row count based on your PCB layout and required pin density. Verify with the datasheet for exact row spacing.

Specifies the number of differential signal pairs arranged in each column of a connector or backplane. This attribute helps engineers assess signal density and routing feasibility for high-speed designs. Verify against the datasheet to ensure the connector supports your required channel count and layout constraints.

Indicates the total number of signal contacts or positions in a connector or socket. Compare this value with your required pin count to ensure proper mating and circuit routing. Always verify against the datasheet for exact configuration.

Physical height of the component, measured from the mounting surface to the topmost point. This dimension is critical for clearance in compact assemblies and for ensuring proper fit within enclosures. Always verify against the datasheet for tolerance and mounting considerations.

Defines the maximum continuous current that a single contact can safely carry. Exceeding this rating may cause overheating, contact degradation, or failure. Check the datasheet for derating curves and ambient temperature effects.

Style or type of the connector, such as D-sub, USB, RJ45, or circular, determining its mechanical interface and electrical performance. Choose the style that matches your mating connector and application environment. Verify the connector style in the datasheet to ensure proper fit, pinout, and durability for your design.

Indicates how many contacts in a connector are designated for ground connection. This is critical for ensuring proper grounding and signal integrity in electronic assemblies. Compare with circuit requirements and verify against connector datasheet for pinout accuracy.

Total number of electrical contacts in the connector, which determines the maximum number of circuits that can be connected. This is a critical parameter for matching the connector to your wire harness requirements. Ensure the contact count aligns with your signal and power needs.

The unique part number assigned by the original component manufacturer. Use this to cross-reference datasheets, verify specifications, and ensure the exact component matches your design requirements. Always confirm the number against the manufacturer's official documentation.

Indicates the floor life of a component before it must be baked prior to soldering. Higher levels require stricter handling and shorter exposure times. Verify the MSL rating in the datasheet to ensure proper storage and assembly conditions.

Harmonized Tariff Schedule of the United States code for customs classification. Essential for import/export documentation and duty calculation. Verify the correct code with a trade specialist to avoid customs delays.

Indicates whether the component complies with the EU RoHS directive restricting hazardous substances. Buyers should verify this status for regulatory compliance and market access. Check the datasheet or certificate for exact compliance details.